Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

APPLICATION


Our silicone products are used in all walks of life

APPLICATION


Our silicone products are used in all walks of life

Application Industry

Silicone vs Polycarbonate vs Acrylic LED Diffusers: A Material Comparison

2026-10-28 12:46:07

Click:

“ A material comparison for LED diffusers: how silicone, polycarbonate and acrylic behave in heat, UV, impact and bending, where each one fails, and how to pick for a strip project. ”

Silicone, polycarbonate and acrylic split along one line: whether the diffuser is cured or melted. Platinum-cured silicone is a thermoset, so it keeps its colour and can bend. Polycarbonate and acrylic are thermoplastics, cheaper to form and more sensitive to ultraviolet light and heat. The better choice follows the project, not a material ranking.

ManufacturingSince 2012FPC range4–28 mmTemperature−40 to +200 °CCapacity14 extrusion lines

Is silicone better than polycarbonate for LED diffusion?

Silicone is the better answer only where the diffuser has to bend, sit in a warm cavity or come off for service. Polycarbonate wins on a straight run in a fixture closed once. The three are not grades of one another: silicone is a platinum-cured thermoset, while polycarbonate and acrylic are thermoplastics shaped by heat.

That difference decides the rest. A thermoset cannot be re-melted, so a silicone sleeve holds its section in a hot cavity and can be pushed onto a bend. A thermoplastic is softened to be formed, so a curved polycarbonate or acrylic lens needs a forming step, and that step sets a minimum radius the design must respect.

What makes a silicone diffuser able to follow a curve?

Flexibility comes from the crosslinked network, not an additive. The siloxane backbone is mobile between crosslink points, which is why the compound sits at 70 ± 5 Shore A and returns to shape after bending. A wall of 0.5 mm to 0.6 mm follows a radius a rigid lens cannot, and the section coils at 200 m per roll. The same body covers FPC from 4 mm to 28 mm, stocks PCB widths of 8, 10 and 12 mm and holds a 2.8 mm inner height.

That flexibility costs support. A soft body does not carry its own line over a long span, so a bent run is held by an aluminum profile or a clip and the diffuser is one part of an assembly. End caps and clips are not made in-house; they are integrated through partner suppliers.

How do the three materials behave under heat and impact?

Temperature shows the chemistry first. The silicone extrusion is rated from −40 °C to +200 °C, with a density of 1.2 ± 0.1 g/cm³, tensile strength of at least 8 MPa, tear strength of at least 30 kN/m and a UL94 HB rating. Because the network is fully reacted, a warm cavity does not soften the body, and creep is not a design term the way it is for a thermoplastic near its softening range.

Impact separates them a second way. Silicone deforms and returns, and an overload shows as a tear at an edge, not a shattered face. Polycarbonate is the toughest of the three, but it crazes and scratches. Acrylic is hard, optically clean and the most brittle: it chips at the fixing, and a chip runs as a crack, which in a diffuser becomes a bright line.

Does silicone yellow over time with LED heat?

The mechanism that yellows a diffuser is largely absent from a platinum-cured silicone. Addition curing reacts the vinyl and hydride groups through a platinum catalyst and leaves no peroxide residue, so little unreacted material remains in the wall to oxidise under heat and light. The siloxane backbone has no group that absorbs strongly in the ultraviolet band, so ultraviolet resistance belongs to the polymer, not to an additive that can be used up.

Polycarbonate fails by a different route. Ultraviolet light and heat attack the carbonate linkage at the surface, and the products absorb blue light, so the face nearest the light reads yellow while the bulk stays clear. Acrylic degrades another way: the ester side groups are attacked, the chain shortens, and toughness is lost to crazing before any colour shift. In both, degradation is set by polymer chemistry, not by how well the part was moulded.

Silicone is not unconditional. Colour can shift outside the −40 °C to +200 °C window, and a clear wall shows a small change earlier than a milky one because the face is read directly. What the platinum cure removes is the built-in oxidation route, a material fact rather than a process claim.

Where does the cost of each material actually sit?

The price of a diffuser is not the cost of the material. Silicone compound costs more per kilogram than polycarbonate or acrylic resin, and the platinum catalyst is part of that premium. Against it sits a cheap tool: standard rounds carry no mould fee, and an extrusion die is a fraction of an injection mould. Because extrusion runs continuously and a stock section is supplied at 200 m per roll, cost per metre barely moves with order size.

Thermoplastic parts invert that curve. Polycarbonate and acrylic are extruded for straight profiles or injection moulded for shaped lenses; the mould is expensive, but the marginal cost per part falls sharply once paid off, so volume favours injection. Every extruded and bonded silicone part also carries a bonding charge, and bonding is still cheaper than compression moulding the same shape.

The last term is the cost of a failure. A yellowed polycarbonate face or a cracked acrylic lens is a replacement part, an access visit and, in a sealed fixture, a new assembly. Silicone is the dearer part and often the cheaper installation over a long service life.

How do installation and repair differ on site?

Installation turns softness into labour. A silicone sleeve is pulled from a 200 m roll over a strip already fixed to a panel, cut to length on site, and replaced a length at a time. Nothing is bonded to the light source, so the diffuser can come off for cleaning and go back on.

A rigid lens works the other way. A polycarbonate or acrylic part is held by screws, a frame or an adhesive, and once a sealed fixture is closed the lens is not meant to come out. Removal is the weak point: acrylic chips at the fixing and polycarbonate scratches, so a repair often means a new lens.

Which material fits which project?

Read the table with one question in mind: does the diffuser carry the shape, or does something else carry it? The comparison is qualitative: failure modes and design consequences, not measured optical values, since none of the three can be ranked without the strip and the cavity.

Point of comparisonSiliconePolycarbonateAcrylic
FlexibilityBends around a corner; needs a profile or clipRigid; a heat-formed bend has a minimum radiusRigid; least forgiving of a tight radius
HeatRated −40 to +200 °C; does not softenNears its softening range; creeps under loadForming heat and service heat share one margin
ImpactDeforms and returns; overload tears, not shattersToughest here, though it crazes and scratchesBrittle; a chip runs as a crack
UV and yellowing mechanismNo peroxide residue to oxidise; no ultraviolet-absorbing groupSurface photo-oxidation yellows the carbonate chainEster groups attacked; embrittlement before colour
Cost structureDearer compound, small die, no mould fee on stock sections; flat per-metre costCheap resin; mould must be amortised, then part cost fallsCheapest straight profile; risk sits in service
Best-fit projectBent runs, warm cavities, serviceable fixturesStraight high-volume runs with a shielded faceStraight decorative runs behind a protected face

If the section and the radius are still open, send both: ask for a project review and the reply comes back with the section, the compound and the support the run needs.

Frequently asked questions

What temperature can a silicone LED diffuser withstand?

The extrusion is rated from −40 °C to +200 °C, and the platinum cure does not soften inside that window. Hardness is 70 ± 5 Shore A, tensile strength at least 8 MPa and tear strength at least 30 kN/m, so a warm cavity does not pull the wall out of its profile.

Does silicone LED sleeve block too much light?

It does not block a fixed share of the output; it changes the shape of it. In a diffusing compound light is diffused rather than pointed, so the face reads as a band instead of a row of dots. Transmittance is adjusted through compound formulation, and the mix is set per project.

Is a silicone diffuser more expensive than a polycarbonate one?

Per part, usually yes: in a silicone vs polycarbonate LED diffuser comparison, the compound and the platinum cure cost more than resin. Per installed fixture, not always: a standard section carries no mould fee, the die is small, and a sleeve can be replaced without a new lens. The two costs move in opposite directions as order size rises.

Can a silicone diffuser hold its line without a profile?

Not over a long span. At 70 ± 5 Shore A the body is soft by design, so a straight run is normally held in a profile or a clip, and a bent run needs support at the curve. Flexibility is an advantage at the shape and a cost at the structure.

What do I send for a material and section quotation?

Send the strip width, the bend radius, the cavity depth and the run length, and say whether the fixture is opened for service. Orders are measured against a USD 500 minimum value, not a minimum length: a stocked item leaves in 5 to 7 working days, a stock sample in 3, and a new section in 10 to 20.

Related reading

Next step

Send the strip width, the bend radius, the cavity depth and the run length. Roll length depends on the body: 200 m for the square, grooved and D sections and 100 m for channel covers. Certificates for ROHS, REACH and UL94 HB sit at material level, and a test report on a finished part is a separate project.

Ready to settle the material?

Send the section, the bend radius and the run length. The material is proposed against the fixture.

Request a quote →WhatsApp +8618028921514

DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Silicone vs Polycarbonate vs Acrylic LED Diffusers: A Material Comparison

Author:DongGuan Yutian Silicone Rubber Technology Co.,Ltd

Silicone, polycarbonate and acrylic split along one line: whether the diffuser is cured or melted. Platinum-cured silicone is a thermoset, so it keeps its colour and can bend. Polycarbonate and acrylic are thermoplastics, cheaper to form and more sensitive to ultraviolet light and heat. The better choice follows the project, not a material ranking.

ManufacturingSince 2012FPC range4–28 mmTemperature−40 to +200 °CCapacity14 extrusion lines

Is silicone better than polycarbonate for LED diffusion?

Silicone is the better answer only where the diffuser has to bend, sit in a warm cavity or come off for service. Polycarbonate wins on a straight run in a fixture closed once. The three are not grades of one another: silicone is a platinum-cured thermoset, while polycarbonate and acrylic are thermoplastics shaped by heat.

That difference decides the rest. A thermoset cannot be re-melted, so a silicone sleeve holds its section in a hot cavity and can be pushed onto a bend. A thermoplastic is softened to be formed, so a curved polycarbonate or acrylic lens needs a forming step, and that step sets a minimum radius the design must respect.

What makes a silicone diffuser able to follow a curve?

Flexibility comes from the crosslinked network, not an additive. The siloxane backbone is mobile between crosslink points, which is why the compound sits at 70 ± 5 Shore A and returns to shape after bending. A wall of 0.5 mm to 0.6 mm follows a radius a rigid lens cannot, and the section coils at 200 m per roll. The same body covers FPC from 4 mm to 28 mm, stocks PCB widths of 8, 10 and 12 mm and holds a 2.8 mm inner height.

That flexibility costs support. A soft body does not carry its own line over a long span, so a bent run is held by an aluminum profile or a clip and the diffuser is one part of an assembly. End caps and clips are not made in-house; they are integrated through partner suppliers.

How do the three materials behave under heat and impact?

Temperature shows the chemistry first. The silicone extrusion is rated from −40 °C to +200 °C, with a density of 1.2 ± 0.1 g/cm³, tensile strength of at least 8 MPa, tear strength of at least 30 kN/m and a UL94 HB rating. Because the network is fully reacted, a warm cavity does not soften the body, and creep is not a design term the way it is for a thermoplastic near its softening range.

Impact separates them a second way. Silicone deforms and returns, and an overload shows as a tear at an edge, not a shattered face. Polycarbonate is the toughest of the three, but it crazes and scratches. Acrylic is hard, optically clean and the most brittle: it chips at the fixing, and a chip runs as a crack, which in a diffuser becomes a bright line.

Does silicone yellow over time with LED heat?

The mechanism that yellows a diffuser is largely absent from a platinum-cured silicone. Addition curing reacts the vinyl and hydride groups through a platinum catalyst and leaves no peroxide residue, so little unreacted material remains in the wall to oxidise under heat and light. The siloxane backbone has no group that absorbs strongly in the ultraviolet band, so ultraviolet resistance belongs to the polymer, not to an additive that can be used up.

Polycarbonate fails by a different route. Ultraviolet light and heat attack the carbonate linkage at the surface, and the products absorb blue light, so the face nearest the light reads yellow while the bulk stays clear. Acrylic degrades another way: the ester side groups are attacked, the chain shortens, and toughness is lost to crazing before any colour shift. In both, degradation is set by polymer chemistry, not by how well the part was moulded.

Silicone is not unconditional. Colour can shift outside the −40 °C to +200 °C window, and a clear wall shows a small change earlier than a milky one because the face is read directly. What the platinum cure removes is the built-in oxidation route, a material fact rather than a process claim.

Where does the cost of each material actually sit?

The price of a diffuser is not the cost of the material. Silicone compound costs more per kilogram than polycarbonate or acrylic resin, and the platinum catalyst is part of that premium. Against it sits a cheap tool: standard rounds carry no mould fee, and an extrusion die is a fraction of an injection mould. Because extrusion runs continuously and a stock section is supplied at 200 m per roll, cost per metre barely moves with order size.

Thermoplastic parts invert that curve. Polycarbonate and acrylic are extruded for straight profiles or injection moulded for shaped lenses; the mould is expensive, but the marginal cost per part falls sharply once paid off, so volume favours injection. Every extruded and bonded silicone part also carries a bonding charge, and bonding is still cheaper than compression moulding the same shape.

The last term is the cost of a failure. A yellowed polycarbonate face or a cracked acrylic lens is a replacement part, an access visit and, in a sealed fixture, a new assembly. Silicone is the dearer part and often the cheaper installation over a long service life.

How do installation and repair differ on site?

Installation turns softness into labour. A silicone sleeve is pulled from a 200 m roll over a strip already fixed to a panel, cut to length on site, and replaced a length at a time. Nothing is bonded to the light source, so the diffuser can come off for cleaning and go back on.

A rigid lens works the other way. A polycarbonate or acrylic part is held by screws, a frame or an adhesive, and once a sealed fixture is closed the lens is not meant to come out. Removal is the weak point: acrylic chips at the fixing and polycarbonate scratches, so a repair often means a new lens.

Which material fits which project?

Read the table with one question in mind: does the diffuser carry the shape, or does something else carry it? The comparison is qualitative: failure modes and design consequences, not measured optical values, since none of the three can be ranked without the strip and the cavity.

Point of comparisonSiliconePolycarbonateAcrylic
FlexibilityBends around a corner; needs a profile or clipRigid; a heat-formed bend has a minimum radiusRigid; least forgiving of a tight radius
HeatRated −40 to +200 °C; does not softenNears its softening range; creeps under loadForming heat and service heat share one margin
ImpactDeforms and returns; overload tears, not shattersToughest here, though it crazes and scratchesBrittle; a chip runs as a crack
UV and yellowing mechanismNo peroxide residue to oxidise; no ultraviolet-absorbing groupSurface photo-oxidation yellows the carbonate chainEster groups attacked; embrittlement before colour
Cost structureDearer compound, small die, no mould fee on stock sections; flat per-metre costCheap resin; mould must be amortised, then part cost fallsCheapest straight profile; risk sits in service
Best-fit projectBent runs, warm cavities, serviceable fixturesStraight high-volume runs with a shielded faceStraight decorative runs behind a protected face

If the section and the radius are still open, send both: ask for a project review and the reply comes back with the section, the compound and the support the run needs.

Frequently asked questions

What temperature can a silicone LED diffuser withstand?

The extrusion is rated from −40 °C to +200 °C, and the platinum cure does not soften inside that window. Hardness is 70 ± 5 Shore A, tensile strength at least 8 MPa and tear strength at least 30 kN/m, so a warm cavity does not pull the wall out of its profile.

Does silicone LED sleeve block too much light?

It does not block a fixed share of the output; it changes the shape of it. In a diffusing compound light is diffused rather than pointed, so the face reads as a band instead of a row of dots. Transmittance is adjusted through compound formulation, and the mix is set per project.

Is a silicone diffuser more expensive than a polycarbonate one?

Per part, usually yes: in a silicone vs polycarbonate LED diffuser comparison, the compound and the platinum cure cost more than resin. Per installed fixture, not always: a standard section carries no mould fee, the die is small, and a sleeve can be replaced without a new lens. The two costs move in opposite directions as order size rises.

Can a silicone diffuser hold its line without a profile?

Not over a long span. At 70 ± 5 Shore A the body is soft by design, so a straight run is normally held in a profile or a clip, and a bent run needs support at the curve. Flexibility is an advantage at the shape and a cost at the structure.

What do I send for a material and section quotation?

Send the strip width, the bend radius, the cavity depth and the run length, and say whether the fixture is opened for service. Orders are measured against a USD 500 minimum value, not a minimum length: a stocked item leaves in 5 to 7 working days, a stock sample in 3, and a new section in 10 to 20.

Related reading

Next step

Send the strip width, the bend radius, the cavity depth and the run length. Roll length depends on the body: 200 m for the square, grooved and D sections and 100 m for channel covers. Certificates for ROHS, REACH and UL94 HB sit at material level, and a test report on a finished part is a separate project.

Ready to settle the material?

Send the section, the bend radius and the run length. The material is proposed against the fixture.

Request a quote →WhatsApp +8618028921514

DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.

Silicone vs Polycarbonate vs Acrylic LED Diffusers: A Material Comparison
A material comparison for LED diffusers: how silicone, polycarbonate and acrylic behave in heat, UV, impact and bending, where each one fails, and how to pick for a strip project.
Long by picture save/share
0

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Products Recommended

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

CONTACT


Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

 

  • Mobile:
  • 0086-18028921514
  • Fax:0086-769-82555312
  • Email:salesmanager@yutiansilicone.com

Link: China Edge-lit Lighting, Backlight Lighting Manufa

Contact Us

Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

 

  • Mobile/Whatsapp:
    0086-18028921514
  • Fax:86-769-89221009
  • Email:salesmanager@yutiansilicone.com

 

Copyright © 2015-2026 All Rights Reserved.

Copyright © 2015-2026 All Rights Reserved.   

Service Center

Please choose online customer service to communicate

Contacts
Phone
+8618028921514
Service time
From Monday to Sunday
E-mail
salesmanager@yutiansilicone.com
Scan a QR Code
Qrcode
WhatsApp
Add WeChat friend to learn more about the product
Use Enterprise WeChat
"Scan" to join the group chat
Copy success!
Add WeChat friend to learn more about the product
I see.