Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided silicone hose for Bubble Tea Machine

Braided silicone hose for bubble tea machines: platinum-cured food-grade silicone with a polyester braid between the walls, built for the steam and hot water unit where steam is pulsed at up to about 190 °C. 4–10 mm ID, wall 2.0–3.0 mm, −40 to +200 °C, FDA 21 CFR 177.2600 and LFGB. Braid and ply count are quoted per line; syrup and drain lines should use clear unreinforced tubing.

    Product Features

    Braided for the steam and hot water unit — the position where steam is pulsed and the line cycles from cold start to full steam, and the one where an unreinforced wall works loose at the fitting
    Food-grade silicone bore — platinum-cured compound with no plasticiser, so nothing migrates into the drink and the cleaning circuit has nothing to leach
    Braid instead of a thicker wall — keeps the bore where it was extruded under pulse load, so the flow rate stays set without the stiffness a heavy wall brings
    Materials documented for food equipment — silicone and colour compound documented to NSF/ANSI 51, with FDA 21 CFR 177.2600 and LFGB statements shipped with the order
    −40 °C to +200 °C continuous — covers every position on the machine, with headroom for the descaling and sanitising cycles
    Braid quoted per line — yarn, angle, coverage and ply count are specified against the load of that line and returned on the quotation

    Application

    Steam and hot water unit
    Steam and hot water circuits, where the braid takes the pulse load and holds the bore.
    Hot water and tea lines
    80–95 °C at close to atmospheric pressure; the braid works as kink resistance.
    Cleaning circuits
    Food-grade acid and chlorine sanitiser, platinum-cured with no plasticiser.
    OEM bubble tea equipment
    Line-by-line specification for machine builders and private-label programmes.
    Replacement parts
    Cut lengths matched to the hose being replaced, same section and braid.
    Custom sections and braid
    Bore, wall, yarn and coverage built to the drawing rather than a fixed list.

  • Parameters

    Product Features

    Braided for the steam and hot water unit — the position where steam is pulsed and the line cycles from cold start to full steam, and the one where an unreinforced wall works loose at the fitting
    Food-grade silicone bore — platinum-cured compound with no plasticiser, so nothing migrates into the drink and the cleaning circuit has nothing to leach
    Braid instead of a thicker wall — keeps the bore where it was extruded under pulse load, so the flow rate stays set without the stiffness a heavy wall brings
    Materials documented for food equipment — silicone and colour compound documented to NSF/ANSI 51, with FDA 21 CFR 177.2600 and LFGB statements shipped with the order
    −40 °C to +200 °C continuous — covers every position on the machine, with headroom for the descaling and sanitising cycles
    Braid quoted per line — yarn, angle, coverage and ply count are specified against the load of that line and returned on the quotation

    Application

    Steam and hot water unit
    Steam and hot water circuits, where the braid takes the pulse load and holds the bore.
    Hot water and tea lines
    80–95 °C at close to atmospheric pressure; the braid works as kink resistance.
    Cleaning circuits
    Food-grade acid and chlorine sanitiser, platinum-cured with no plasticiser.
    OEM bubble tea equipment
    Line-by-line specification for machine builders and private-label programmes.
    Replacement parts
    Cut lengths matched to the hose being replaced, same section and braid.
    Custom sections and braid
    Bore, wall, yarn and coverage built to the drawing rather than a fixed list.
Yutian · bubble tea · braided silicone hose · food grade

A bubble tea shop runs six machines — the braid belongs on one of them

A braided silicone hose for a bubble tea machine is a food-grade silicone tube with a braid laid between an inner and an outer silicone wall. It earns its place on the steam and hot water unit, where steam is pulsed and the line cycles from cold start to full steam several times an hour. On the syrup dispenser the answer is the opposite: low pressure, and the operator has to see the syrup, so clear unreinforced tubing is the right part.

Steam and hot water unitFDA 21 CFR 177.2600 & LFGB4–10 mm ID−40 °C to +200 °CFood-grade silicone

A bubble tea shop runs six machines, not one

The phrase bubble tea machine covers a counter full of equipment with different jobs. Only two of them move fluid under pressure, and only one of those is the reason a braid exists. That distinction decides whether a page like this one is talking to your buyer or past them.

MachineBraided hoseWhy
Steam and hot water unitYesPulsed steam, hot water and a wand that is bent all day
Fructose / syrup dispenserNoLow-pressure metering pump; the syrup has to stay visible
Cup sealing machineNot applicableNo fluid circuit
Shaker machineNot applicableNo fluid circuit
Boba cookerRarelyDrain side should stay clear
Ice makerDepends on modelCovered on the ice machine hose page

Most enquiries that say bubble tea machine hose are really about the steam and hot water unit. That is the unit with a steam valve, a hot water tap and a wand, and it is the one where the hose has a measurable job. If your line is the syrup dispenser, this is the wrong component and we will say so rather than quote it.

Where the braid belongs, and what it is doing there

Steam circuit — the demanding position

The steam run is pulsed rather than steady. Documented commercial duty on bubble tea equipment runs at pressure pulses around 15 bar with steam up to about 190 °C, and the line cycles from a cold start to full steam several times an hour. Those cycles are what a reinforced wall is for: an unreinforced wall softens, balloons slightly and eventually works loose at the fitting, and the failure usually appears at the joint rather than in the middle of the run.

Hot water and tea — kink resistance, not pressure

Hot water and brewed tea sit between 80 and 95 °C at close to atmospheric pressure. What the braid buys here is not pressure containment, it is kink resistance: a counter packs a lot of bends into a small footprint, and a hose that flattens at a bend changes the flow without looking any different from outside.

Cleaning circuit and inlet

The cleaning circuit runs food-grade acid during descaling and chlorine-based sanitiser during sanitising, at pump pressure. Platinum-cured silicone with no plasticiser is the right compound because nothing can migrate into the solution and from there into the next drink. The inlet runs near atmospheric pressure; a braid there is about routing and drag wear, not pressure.

Drain and overflow — keep them clear

Drain and overflow are gravity flow. Use clear unreinforced tubing: you need to see scale, biofilm and whether it drains at all, and an opaque braid removes exactly that information.

When a braided hose is the wrong part

This is the part of the page most suppliers leave out, and the part a buyer remembers.

The syrup line

The problem there is crystallisation, not pressure. A braid is opaque, so it hides the one condition the operator needs to watch. Metering-pump pressure gains nothing from reinforcement.

Drain and overflow

Atmospheric gravity flow. Nothing to contain, and a technician may need to watch whether it drains before ordering a part.

Service runs you open daily

Repeated plugging works the cut end. If the line is broken and remade every day, a smooth wipeable wall is worth more than reinforcement.

Anything you need to see through

Scale, biofilm, syrup colour, air bubbles. Clear tubing answers questions that an opaque braid turns into a service call.

How the braid on this hose is specified

Braid is not one thing. Yarn, angle, coverage and ply count are separate choices, and they are made against the load the line actually carries. That is why we quote the braid per line instead of publishing one configuration and applying it to every position in the machine.

A steam run, a hot water run and a cleaning circuit do not see the same load, so they are not priced as the same hose. Send the position and the pressure behaviour of that run — steady or pulsed, and the peak if it is pulsed — and the braid for that line is quoted against it. Coverage and ply count are set at the winder, and they come back on the quotation rather than on this page, because a number printed here would be the wrong number for most buyers.

The braid also does dimensional work. Under pulse load a reinforced wall still moves a little; the point of the reinforcement is to keep the bore where it was extruded so the flow rate stays where it was set. Independent of any number, that is the reason the part is specified at all.

Section choice is explained on the braided silicone hose range; the hotter end of the range is on the steam hose page, and the heavier mesh build is on the mesh reinforced hose page.

Operating conditions per position

The ranges below are what the machine side publishes for bubble tea equipment. They are a starting point for the compound and the braid, not a specification of the hose: quote against the position, not against the machine class.

PositionPressureTemperatureMedium
Steam circuit15 bar-class pulsesup to about 190 °CSaturated steam
Hot water and teaNear atmospheric80–95 °CDrinking water, brewed tea
Syrup lineMetering pump, lowAmbientHigh-viscosity fructose
Cleaning circuitPump dependentAmbient to warmFood-grade acid, chlorine sanitiser
InletAtmospheric to 0.3 MPaAmbientMains water

Our own rating for the hose is −40 °C to +200 °C continuous. That covers every position on the machine with headroom, and the thermal stress that ages a steam line is not the headline peak but the repeat: cold start, full steam, cold again, several times an hour.

Sizes, wall thickness and connections

Bubble tea equipment has not settled on a fixed set of sections the way espresso machines have, so select by line rather than by machine model.

Inner diameterTypical position
4–5 mmFructose dispenser outlet, small internal runs
6–8 mmMost common — inlet, hot water and tea main
8–10 mmSteam circuit and high-flow dispensing

Wall thickness of 2.0–3.0 mm covers most positions. The steam run is where the wall matters most, so it is where the section is worth confirming against the fitting rather than assumed.

If the connection is imperial, 1/4 inch is 6.35 mm and 5/16 inch is 7.94 mm. A 6 mm hose is not a 1/4 inch hose, and the difference shows up as a leak at the barb rather than as a measurement error on paper. Say which system the drawing came in when you send it.

Food-contact documents, and what they cover

Two different things get called FDA. One is a material declaration: the compound documented against FDA 21 CFR 177.2600, the clause for rubber in repeated food contact. The other is a product test report: a specific bore, wall and braid, tested at a specific temperature against a specific food simulant. A machine builder working towards a unit certificate needs the second; a purchasing team checking a supplier usually asks for the first.

StandardWhat it coversWhere it sits for this hose
FDA 21 CFR 177.2600US food contact, repeated useMaterial declaration for the compound
LFGBGerman food contact law, sensory testingThe de facto gate for the EU market
(EU) 1935/2004EU food contact frameworkDeclarations and migration basis
NSF/ANSI 51Food equipment materialsThe level the silicone and colour compound are documented against
RoHS / REACHRestricted substances and SVHCDeclarations on request

The braid in this hose sits under a silicone skin, and the colour goes in as a food-grade silicone compound rather than a pigment paste on exposed yarn. That is what lets the material be documented to NSF/ANSI 51: there is no exposed yarn and no second vulcanising pass over paste. It is a materials statement, not a certificate for the part — product-level testing is arranged per project, and the certificate for the assembled machine sits with the builder.

The compound is platinum-cured with no plasticiser, which is the answer to the cleaning question: food-grade acid and chlorine sanitiser both meet a wall that has nothing to leach. The tube is not for human implantation.

What you can specify

Bore and wall

Built to the drawing. Bores are quoted against the position rather than a fixed table of sections, wall 2.0–3.0 mm for most lines.

Braid yarn

Polyester for the general case, aramid where the line runs hot or close to a heater. The yarn is chosen with the temperature and the abrasion in mind.

Braid construction

Angle, coverage and ply count are set at the winder and quoted against the load of that line. This is the choice that decides how the hose behaves under pulse load.

Length and ends

Cut to length or coiled, bare ends for your own barb or clamp. Where an assembly is needed, non-silicone fittings are integrated through partner manufacturers — we make the silicone part.

Production runs on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, up to 8 million metres a month, since 2012. Material documents ship with the order; the plant runs ISO 9001 and ISO 13485.

What to send for a quote

Six items usually close the technical questions in one round instead of four.

SendWhy it matters
Line position — steam, hot water, syrup, cleaning or inletDecides whether a braid is the right part at all
ID and OD, or ID plus wallMetric preferred; say if the fitting is imperial
Pressure behaviour — steady or pulsed, and the peakSets the braid for that line
Medium temperature, normal and peakSets the compound grade
Cleaning chemicals usedAcid descaling and chlorine sanitising need separate confirmation
Connector type and sizeBarb, quick-connect or clamp — send the drawing or a sample

Standard sections ship in 5 to 7 working days, stock samples in 3 days, and a custom construction takes 10 to 20 working days. Samples of stock sections are free; freight is paid by the buyer.

Questions buyers ask before they specify

What is a bubble tea machine hose made of?

Food-grade platinum-cured silicone, with a polyester braid laid between an inner and an outer silicone wall. Platinum curing keeps the compound free of peroxide residues, so there is no odour or taste transfer into the drink.

Does every line on a bubble tea machine need a braided hose?

No. The steam circuit and high-flow dispensing lines need one. Syrup lines, drain lines and gravity returns should use clear unreinforced tubing, because the operator needs to see flow and residue.

Why not use a braided hose on the syrup line?

Because the problem there is crystallisation, not pressure. A braid is opaque, so it hides the condition you need to watch. Syrup lines run at metering-pump pressure and gain nothing from reinforcement.

How many braid plies do I need?

It depends on the line, and it is quoted per line rather than published as one number. Send the position and the pressure behaviour — steady or pulsed, and the peak — and the braid is specified against it.

What pressure does the steam circuit see?

Documented commercial duty on bubble tea equipment runs at pressure pulses around 15 bar with steam up to about 190 °C. That is why the steam position is the one that fails first on an under-specified hose.

What temperature does the hose take?

−40 °C to +200 °C continuous. That covers every position on the machine; the stress that ages a steam line is the repeat of cold start to full steam, not the peak on its own.

Which certification do I need for the EU and the US?

FDA 21 CFR 177.2600 for the US and LFGB for the EU cover most requests. Add NSF/ANSI 51 when a North American buyer specifies food equipment materials.

Can the hose handle daily cleaning?

Yes, provided the compound is platinum-cured with no plasticiser. The cleaning circuit is chemically aggressive rather than hot, and silicone resists both food-grade acid and chlorine-based sanitiser without leaching.

What sizes are most common?

6–8 mm ID for inlet, hot water and tea lines, 4–5 mm for fructose dispenser outlets, and 8–10 mm for the steam circuit and high-flow dispensing.

What lead time should I plan for?

Standard sections in 5 to 7 working days, stock samples in 3 days, custom bore and wall in 10 to 20 working days after approval.

Need a hose for a bubble tea machine line?

Send the machine, the line position and the section. If the line is a syrup or drain run, we will tell you so and point you at clear tubing instead.

Request a quote

WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com

Braided silicone hose for Bubble Tea Machine
Braided silicone hose for bubble tea machines: platinum-cured food-grade silicone with a polyester braid between the walls, built for the steam and hot water unit where steam is pulsed at up to about 190 °C. 4–10 mm ID, wall 2.0–3.0 mm, −40 to +200 °C, FDA 21 CFR 177.2600 and LFGB. Braid and ply count are quoted per line; syrup and drain lines should use clear unreinforced tubing.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided silicone hose for Bubble Tea Machine

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.