Demand Submission
Please leave us a message and we will contact you within 24 hours
PRODUCTS
Specializing in the production of highquality silicone rubber products
PRODUCT
Specializing in the production of highquality silicone rubber products
— Product Categories
-
Silicone tube -
LED light strip silicone sleeve -
Foamed silicone tube -
Silicone braided tube -
Medical silicone tube -
Peristaltic pump silicone hose -
Communication/power shrink tubing -
Silicone shielding strip -
Foam silicone sealing strip -
Silicone sealing strip/ring -
Bicycle handle cover/strap -
Silicone sheets and miscellaneous parts -
Silicone leather
— News Recommended
-
top Introducing the Innovative Foam Silicone Tube:...
-
top Enhancing the Lifespan of High-Temperature Sil...
-
top Colored Silicone Tube: Production Process and ...
-
Custom Silicone Foam Tube: Sizes, Colors, and ...
-
UL94 V-0 Silicone Foam Tube for EV Battery Pro...
-
Food Grade Silicone Foam Insulation Tube: FDA ...
-
Silicone Foam Tube vs EPDM Rubber Foam: Which ...
-
Platinum-Cured vs Peroxide-Cured Silicone Foam...
— Products Recommended
INQUIRY
Add Successfully
Mesh Reinforced Silicone Hose
Mesh reinforced silicone hose: a platinum-cured silicone bore, two braid plies (cotton standard) and an outer silicone jacket, bonded into one 4.5 mm wall. Seven published sections from ID 19 mm to 102 mm, burst 0.49–1.47 MPa, bend radii 54–360 mm, −40 °C to +200 °C, food and medical grade silicone.
Product Features
Mesh reinforced silicone hose: a platinum-cured silicone bore, two braid plies and an outer silicone jacket, bonded into one 4.5 mm wall
Braid yarn is selectable — cotton is the standard, other yarns on request — so the hose is matched to the duty
Large bores: seven published sections from ID 19 mm to 102 mm, with burst figures and bend radii
Burst 0.49–1.47 MPa as a minimum; working pressure is the burst figure divided by your safety factor and is quoted per line
Two plies hold the bore under full vacuum and resist kinking at the published bend radius
−40 °C to +200 °C continuous; 70 Shore A, ≥8.6 MPa tensile, ≥360% elongation, ≥32 kN/m tear; food and medical grade materials
Application
Food and beverage transfer
Milk, syrup, juice and CIP lines in a large bore that stays cleanable.
Pharmaceutical and cosmetic
Media transfer with a platinum-cured bore and covered braid.
Water treatment and filtration
Filter feed, backwash and dosing runs under pump pulses.
Chemical and solvent lines
No peroxide residue and no plasticiser to migrate into the medium.
Vacuum and suction service
Two plies keep the bore open where a plain tube collapses.
Equipment OEM and skid builders
Repeatable bore, published burst figure and a fixed cut length.
- Parameters
Product Features
Mesh reinforced silicone hose: a platinum-cured silicone bore, two braid plies and an outer silicone jacket, bonded into one 4.5 mm wall
Braid yarn is selectable — cotton is the standard, other yarns on request — so the hose is matched to the duty
Large bores: seven published sections from ID 19 mm to 102 mm, with burst figures and bend radii
Burst 0.49–1.47 MPa as a minimum; working pressure is the burst figure divided by your safety factor and is quoted per line
Two plies hold the bore under full vacuum and resist kinking at the published bend radius
−40 °C to +200 °C continuous; 70 Shore A, ≥8.6 MPa tensile, ≥360% elongation, ≥32 kN/m tear; food and medical grade materials
Application
Food and beverage transfer
Milk, syrup, juice and CIP lines in a large bore that stays cleanable.
Pharmaceutical and cosmetic
Media transfer with a platinum-cured bore and covered braid.
Water treatment and filtration
Filter feed, backwash and dosing runs under pump pulses.
Chemical and solvent lines
No peroxide residue and no plasticiser to migrate into the medium.
Vacuum and suction service
Two plies keep the bore open where a plain tube collapses.
Equipment OEM and skid builders
Repeatable bore, published burst figure and a fixed cut length.
Yutian · mesh reinforced · two braid plies · ID 19–102 mm
A mesh reinforced silicone hose for large bores and long runs
A mesh reinforced silicone hose is a large-bore silicone hose built as four layers: a platinum-cured silicone bore, two braid plies and an outer silicone jacket, bonded into one wall. The two plies hold the bore against pressure and vacuum, the jacket keeps the braid covered, and the hose stays flexible and clean from −40 °C to +200 °C.
ID 19–102 mmTwo braid plies−40 °C to +200 °CBurst 0.49–1.47 MPaFood and medical gradeWhat a mesh reinforced silicone hose is
Four layers, built in one extrusion and braiding sequence. The bore is a platinum-cured, high-transparency silicone tube. Over it sit two braid plies: the first binds the bore, the second carries the rest of the hoop load. An outer silicone jacket closes the sandwich, so the braid is covered and the hose keeps a smooth outside wall.
Two plies are what make the large bores work. A single braid on a 102 mm bore would let the wall bulge between the yarns; the second ply closes that gap, which is why the wall can stay at 4.5 mm across the whole range instead of growing with the bore. The same two plies hold the bore open under vacuum — the usual reason a buyer moves from a plain tube to a reinforced hose.
Cotton is the standard yarn. The braid can be run in other yarns on request, so a line can be matched to its duty rather than the other way round. Nominal hardness is 70 Shore A; tensile strength is ≥ 8.6 MPa, elongation at break ≥ 360% and tear strength ≥ 32 kN/m on the silicone compound. The small-bore construction in the same family is described in how the three-layer polyester braid is built.
Not for human implantation.
Seven sections, ID 19 mm to 102 mm
These are the sections we publish figures for. The wall stays at 4.5 mm across the range and the burst figure falls as the bore grows: 1.47 MPa at ID 19 mm, 0.49 MPa at ID 102 mm. That is normal for a reinforced hose — the same two plies are carrying a much larger diameter, so the load per metre of yarn goes up.
| Model | ID (mm) | OD (mm) | Wall (mm) | Burst (MPa) | Bend radius (mm) |
|---|---|---|---|---|---|
| YT-GB-4019 | 19 | 28 | 4.5 | ≥ 1.47 | 54 |
| YT-GB-4025 | 25 | 34 | 4.5 | ≥ 1.28 | 90 |
| YT-GB-4035 | 35 | 44 | 4.5 | ≥ 1.08 | 161 |
| YT-GB-4040 | 40 | 49 | 4.5 | ≥ 0.88 | 200 |
| YT-GB-4051 | 51 | 60 | 4.5 | ≥ 0.69 | 245 |
| YT-GB-4076 | 76 | 85 | 4.5 | ≥ 0.59 | 308 |
| YT-GB-4102 | 102 | 111 | 4.5 | ≥ 0.49 | 360 |
Burst values are minimums, given in MPa. Each pack holds 1–4 m; cut lengths and coils are quoted per order.
A bore outside this list, or a different braid count for a specific pressure, is quoted per project: the bore is set at the die and the braid on the machine, so it is an order rather than a new product line.
Burst is the published figure — working pressure follows your safety factor
The burst figure is a minimum, measured on a new hose. We do not publish one working pressure for the whole range, because the right working pressure is the burst figure divided by the factor your process, standard or customer drawing requires. A 19 mm line and a 102 mm line in the same plant rarely use the same factor.
Tell us the bore, the fluid, the temperature and the factor. The quote carries the working pressure for your line rather than a headline number that would be wrong for most of them.
Mesh reinforced hose or plain silicone tube?
Both are silicone, both are clean and both are flexible. The braid is what changes the job: it is the difference between a tube that carries fluid and a hose that holds its shape while it does.
| Property | Mesh reinforced hose | Plain silicone tube |
|---|---|---|
| Reinforcement | Two braid plies between bore and jacket | None — silicone wall only |
| Vacuum | Bore stays open under full vacuum | Collapses inward |
| Kinking | Resists kinking at the published bend radius | Kinks and closes under a tight bend |
| Large bores | Reaches ID 102 mm with a 4.5 mm wall | Gets stiff and heavy well before that |
| Bore stability | Holds its bore under pressure, so flow stays steady | Bore grows under pressure |
If the line runs at atmospheric pressure and you only need flexibility, a plain tube is the cheaper answer. If the line sees vacuum, a pump pulse or a long unsupported run, the reinforced build is the one that keeps its bore. For smaller bores at higher pressure, the three-layer braided silicone hose range is the closer fit — the two families do not share burst figures, so compare them on the page that matches your bore.
Where a mesh reinforced silicone hose is used
Food and beverage transfer
Milk, syrup, juice and CIP lines where a large bore has to stay cleanable and transparent.
Pharmaceutical and cosmetic
Media and product transfer where the bore is platinum-cured and the braid stays covered.
Water treatment and filtration
Filter feed, backwash and dosing runs that see pump pulses and vacuum on the suction side.
Chemical and solvent lines
Platinum-cured bore with no peroxide residue and no plasticiser to migrate into the medium.
Vacuum and suction service
Two plies hold the bore open on suction runs, which is where a plain tube collapses.
Equipment OEM and skid builders
Repeatable bore, published burst figure and a fixed cut length for a machine that ships.
Three affiliated companies, one silicone chain
The hose is the last step of a chain we control from the compound up: raw material, compounding and the finished hose are handled by three affiliated companies, and Yutian ships the hose you buy.
Guilin Yutian New Materials
Silicone raw material and compound development, 28,000 m² site.
Dongguan Huahong Rubber and Plastic
Compounding, auxiliaries and batch control before extrusion.
Dongguan Yutian Silicone
Extrusion, braiding and finishing in a 6,800 m² plant.
What you can specify
Braid yarn
Cotton is the standard yarn. The braid can be run in other yarns on request, so the hose matches the duty rather than the other way round.
Bore and length
Seven published sections from ID 19 to 102 mm, cut to length or coiled, ends bare for your own end treatment.
Colour
Transparent is standard. Opaque and tinted compounds follow a Pantone reference.
Assemblies
Fittings, clamps and connectors are supplied through partner manufacturers; they are not made in-house, but an assembled hose can ship as one part number.
One note that saves a round of samples: the braid is what carries the burst load, so a pressure target is met by changing the braid count and the wall, not by thickening the bore. Tell us the working pressure and the bore, and the quote names the construction.
Lead time, samples and tooling
Published sections
Ship in 5 to 7 working days from stock compounds.
Samples
Stock samples leave in 3 days and are free; freight is paid by the buyer.
Custom construction
10 to 20 working days, depending on the yarn and the end treatment.
Tooling
A bore or construction outside the published sections is quoted per project, with tooling at USD 100–400 per product.
Materials, documents and limits
Material compliance: FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS. The plant runs an ISO 9001 and ISO 13485 quality system, and ISO 10993 biocompatibility reports are issued on request. Certificates travel with the shipment; third-party testing is arranged when your process needs a report rather than a certificate.
Limits worth stating up front: this is a silicone hose, not a hydraulic hose. Where a drawing calls for a high-pressure hydraulic or fuel line, the material is the wrong one and we will say so. The hose is not for human implantation.
The hose is extruded, braided and jacketed on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, at a monthly capacity of up to 8 million metres, since 2012.
Questions buyers ask before they specify
What is a mesh reinforced silicone hose?
A large-bore silicone hose with two braid plies bonded between a platinum-cured bore and an outer silicone jacket. The plies carry the hoop load, so the bore holds its shape under pressure and vacuum; the jacket keeps the braid covered.
What is the braid made of?
Cotton is the standard yarn, and the braid can be run in other yarns on request. The yarn is chosen per duty; tell us the fluid, the temperature and the working pressure and we quote the braid that fits.
Which sizes are published?
Seven sections, ID 19 mm to 102 mm, all with a 4.5 mm wall and a published burst figure and bend radius. Bores outside the list are quoted per project.
What pressure does it hold?
Burst is 0.49–1.47 MPa depending on the bore, measured as a minimum on a new hose. Working pressure is the burst figure divided by the safety factor your process requires, and we quote that per line rather than publishing one headline number.
Can it take vacuum?
Yes. Two braid plies hold the bore open instead of letting the wall collapse, which is the usual reason a buyer moves from a plain tube to a reinforced hose on a suction line.
What temperature range?
−40 °C to +200 °C continuous, the standard range for the silicone compound used in this hose.
Is it food and medical grade?
The compound is supported by FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS documentation, and finished-part reports including ISO 10993 are issued per project on request. The hose is not for human implantation.
What is the lead time and can I get a sample?
Published sections ship in 5 to 7 working days, and stock samples leave in 3 days. Custom constructions take 10 to 20 working days. Stock samples are free; freight is paid by the buyer.
Need a large-bore silicone hose for a food, water or vacuum line?
Send the bore, the working pressure or the safety factor, the fluid and the temperature. You get the section, the burst figure and a sample date back.
Request a quoteWhatsApp +86 18028921514 · salesmanager@yutiansilicone.com
Copy product links
Long by picture save/share
INQUIRY
Add Successfully
INQUIRY
Add Successfully
— News Recommended
-
top Introducing the Innovative Foam Silicone Tube: A High-Perfor...
-
top Enhancing the Lifespan of High-Temperature Silicone Tubes in...
-
top Colored Silicone Tube: Production Process and How to Choose
-
Custom Silicone Foam Tube: Sizes, Colors, and Specifications...
-
UL94 V-0 Silicone Foam Tube for EV Battery Protection: Safet...
-
Food Grade Silicone Foam Insulation Tube: FDA Compliance and...
— Products Recommended
Message
Hi！If you are looking for custom-made silicone rubber products, feel free to ask me any questions.
Brown Di
Brown Di
