Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided silicone tube for oxygen concentrator

Oxygen concentrator braided silicone hose: a platinum-cured medical grade silicone bore, a polyester braid and an outer jacket bonded into one wall. ISO 10993 reports on request, ISO 13485 and ISO 9001 quality systems, full vacuum, burst 1.18–3.73 MPa by bore, −40 °C to +200 °C, ID 3–31.75 mm published sections.

    Product Features

    Medical grade braided silicone hose for the oxygen path inside a concentrator: platinum-cured silicone bore, polyester braid and outer jacket, bonded into one wall
    ISO 10993 biocompatibility reports (cytotoxicity, skin sensitisation, skin irritation) issued per part on request, under an ISO 9001 and ISO 13485 quality system
    Material compliance to FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS; no peroxide residue and no plasticiser in the wall
    Holds pressure pulses and full vacuum: burst 1.18–3.73 MPa by bore, working pressure quoted against your safety factor
    Smooth non-porous bore, rated −40 °C to +200 °C continuous, so steam sterilisation temperatures sit inside the material range
    Eleven published sections from ID 3 mm to 31.75 mm with bend radii 35–200 mm; concentrator lines usually take ID 3–8 mm

    Application

    Home oxygen concentrators
    Internal run from the product tank to the outlet.
    Hospital central supply
    Flexible section between concentrator and wall outlet.
    Ambulance and emergency
    Portable units handled and coiled every shift.
    Clinics and rehabilitation
    Equipment cleaned between patients and audited.
    Veterinary oxygen supply
    Concentrator duty in a smaller enclosure.
    Concentrator OEMs
    Repeatable bore, published burst figure, documented material.

  • Parameters

    Product Features

    Medical grade braided silicone hose for the oxygen path inside a concentrator: platinum-cured silicone bore, polyester braid and outer jacket, bonded into one wall
    ISO 10993 biocompatibility reports (cytotoxicity, skin sensitisation, skin irritation) issued per part on request, under an ISO 9001 and ISO 13485 quality system
    Material compliance to FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS; no peroxide residue and no plasticiser in the wall
    Holds pressure pulses and full vacuum: burst 1.18–3.73 MPa by bore, working pressure quoted against your safety factor
    Smooth non-porous bore, rated −40 °C to +200 °C continuous, so steam sterilisation temperatures sit inside the material range
    Eleven published sections from ID 3 mm to 31.75 mm with bend radii 35–200 mm; concentrator lines usually take ID 3–8 mm

    Application

    Home oxygen concentrators
    Internal run from the product tank to the outlet.
    Hospital central supply
    Flexible section between concentrator and wall outlet.
    Ambulance and emergency
    Portable units handled and coiled every shift.
    Clinics and rehabilitation
    Equipment cleaned between patients and audited.
    Veterinary oxygen supply
    Concentrator duty in a smaller enclosure.
    Concentrator OEMs
    Repeatable bore, published burst figure, documented material.
Yutian · medical grade · oxygen concentrator hose · platinum-cured

A braided silicone hose built for the oxygen path in a concentrator

This is a medical grade braided silicone hose for the oxygen line inside an oxygen concentrator: a platinum-cured silicone bore, a high-temperature polyester braid and an outer silicone jacket, bonded into one wall. The braid keeps the bore round under the pressure pulses and the vacuum on the swing side, and the silicone keeps the oxygen path clean from −40 °C to +200 °C.

ISO 10993 reportsISO 13485 systemFull vacuumBurst 1.18–3.73 MPa−40 °C to +200 °C

Where the hose sits in an oxygen concentrator

A pressure-swing concentrator pushes oxygen-rich gas out of its sieve beds in short cycles. The hose carries that gas from the product tank to the outlet, and on the swing side it sees the reverse: vacuum, and a line that a soft wall would collapse into. Both directions are why the braid is there. A reinforced bore stays round under the pulse and under vacuum, so the flow the machine was set up for does not change as the hose ages.

The same hose is used between the concentrator and the patient line, inside portable and ambulance units, and on central supply runs in hospitals and clinics. In every case the duty is the same: keep the bore open, keep the wall clean, and do not add odour or plasticiser to the gas stream.

Medical grade, stated as documents

“Medical grade” is not a colour or a compound name — it is a set of documents. On this hose the documents are:

ISO 10993 biocompatibility reports (cytotoxicity, skin sensitisation, skin irritation) — issued for the part per project on request. Material compliance to FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS. The plant runs an ISO 13485 and ISO 9001 quality system, so the batch records, material certificates and change control that a device maker audits are already in place.

The compound is platinum-cured, which matters for an oxygen path: no peroxide residues and no plasticiser in the wall, so nothing migrates into the gas stream. It is transparent, so a technician can see the bore. It is not for human implantation, and we say so on the page rather than leaving it to the footnote.

Pressure, vacuum and kinking

The braid carries the hoop load. Burst is published as a minimum per bore, 1.18–3.73 MPa across the eleven sections, and the bore is rated for full vacuum without collapsing. Working pressure is not a single number: it is the burst figure divided by the safety factor your device qualification uses, and we quote it against that factor.

The same braid resists kinking. Bend radii run from 35 mm on the small bores to 200 mm at ID 31.75 mm, which matters inside a concentrator cabinet where the hose is routed around the compressor and the sieve canisters rather than laid straight.

Cleaning and disinfection

The bore is smooth and non-porous, so it can be flushed, wiped and drained rather than brushed. The hose is rated to 200 °C continuous, which puts steam sterilisation temperatures inside the material range, and the platinum-cured wall has no plasticiser to migrate during a cycle.

The cycle itself — temperature, pressure, hold time, number of cycles — is validated on the assembled device, because fittings, connectors and the way the hose is packaged decide the result as much as the tube does. Tell us the method your device uses (steam, chemical wipe, ethylene oxide) and the hose is quoted for that duty rather than for a generic claim.

Published sections: ID 3 mm to 31.75 mm

The braided range runs in eleven published sections, each with a burst figure and a bend radius. Concentrator lines usually take the small end of the range — ID 3, 4, 5, 6 or 8 mm — because the flow is set by the machine, not by the hose. Other bores between the sections are made to order.

ModelID (mm)OD (mm)Wall (mm)Burst (MPa)Bend radius (mm)
HJBX-0013 ± 0.58 ± 0.52.5≥ 3.7335
HJBX-0024 ± 0.59 ± 0.52.5≥ 3.7335
HJBX-0035 ± 0.511 ± 0.53≥ 3.7335
HJBX-0046.35 ± 0.512 ± 0.52.825≥ 3.4335
HJBX-0057.93 ± 0.515 ± 0.53.535≥ 3.4350
HJBX-0069.52 ± 0.517 ± 0.53.74≥ 3.4350
HJBX-00712.7 ± 0.722 ± 0.74.65≥ 2.4570
HJBX-00815.87 ± 0.725 ± 0.74.565≥ 2.2680
HJBX-00919.05 ± 0.731 ± 0.75.975≥ 1.77110
HJBX-01025.4 ± 0.738 ± 0.76.3≥ 1.18150
HJBX-01131.75 ± 0.746 ± 0.77.125≥ 1.18200

Burst values are minimums, given in MPa. Tolerances are ±0.5 mm up to ID 9.52 mm and ±0.7 mm above that. Each pack holds 1–15 m; cut lengths and coils are quoted per order.

Braided silicone hose or PVC oxygen tubing?

PVC tubing is the usual choice for a short patient lead: it is light, cheap and flexible. It is not the usual choice inside the machine, or anywhere the line sees vacuum, heat or a cleaning cycle, because the plasticiser that makes PVC soft is also what limits it.

PropertyBraided silicone hosePVC oxygen tubing
CompoundPlatinum-cured silicone, no plasticiserPVC softened with plasticiser
Temperature−40 °C to +200 °C continuousSoftens and yellows well below that
Plasticiser migrationNone in the wallPlasticiser can migrate over time
VacuumBraid holds the bore openCollapses and kinks on suction
CleaningSmooth non-porous bore, steam inside the ratingWipe only, heat limits the cycle
OdourOdourlessCan carry a plastic odour when new

The general construction and the braid are described on the braided silicone hose range, and the engineering side — how the braid is bonded and what it does to the bore — is worked through in how the three-layer polyester braid is built. For the device-level view of a concentrator line, see the oxygen concentrator hose guide.

Where this hose is used

Home oxygen concentrators

The internal run from the product tank to the outlet, in a cabinet where the hose is routed around the compressor.

Hospital central supply

The flexible section between the concentrator or manifold and the wall outlet run.

Ambulance and emergency units

Portable concentrators where the hose is coiled, uncoiled and handled every shift.

Clinics and rehabilitation

Oxygen therapy equipment that is cleaned between patients and audited by the clinic.

Veterinary oxygen supply

The same concentrator duty in a smaller enclosure, where a 4 mm bore is often the whole line.

Concentrator OEMs

Machine builders who need a repeatable bore, a published burst figure and a documented material for their own device file.

Three affiliated companies, one silicone chain

The hose is the last step of a chain we control from the compound up: raw material, compounding and the finished hose are handled by three affiliated companies, and Yutian ships the hose you buy.

Guilin Yutian New Materials

Silicone raw material and compound development, 28,000 m² site.

Dongguan Huahong Rubber and Plastic

Compounding, auxiliaries and batch control before extrusion.

Dongguan Yutian Silicone

Braiding, extrusion and finishing in a 6,800 m² plant.

What you can specify

Bore and wall

ID 3–31.75 mm in the published sections, wall from 1.5 mm up, with a smaller bore matched to your connector.

Braid yarn

Polyester is standard; aramid is available for the hotter end of the range, and cotton or nylon for other duties.

Length and ends

Cut to length or coiled, ends bare for your own connector, or supplied as an assembly through partner manufacturers.

Documentation

Material certificates with the shipment; ISO 10993 reports, ISO 13485 system evidence and third-party testing arranged per project.

Lead time, samples and tooling

Published sections

Ship in 5 to 7 working days from stock compounds.

Samples

Stock samples leave in 3 days and are free; freight is paid by the buyer.

Custom construction

10 to 20 working days, depending on the yarn and the end treatment.

Tooling

A bore or construction outside the published sections is quoted per project, with tooling at USD 100–400 per product.

Documents, cleanroom and limits

Documents that travel with a shipment: material certificates to FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS; batch traceability under the ISO 9001 and ISO 13485 quality systems. ISO 10993 biocompatibility reports (cytotoxicity, skin sensitisation, skin irritation) are issued per part on request, and third-party testing is arranged when your device file needs a report rather than a certificate.

Production runs on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, at a monthly capacity of up to 8 million metres, since 2012.

Limits worth stating up front: the hose is not for human implantation, it is not a breathing circuit tube for long-term ventilator use, and it is not a substitute for a device-level validation. If your drawing asks for a hose that carries a sterilisation claim, the claim is validated on your assembly — we supply the documented hose that goes into it.

Questions buyers ask before they specify

What tubing do oxygen concentrators use?

A concentrator uses a reinforced silicone hose for the internal oxygen path, because the line sees pressure pulses on the delivery side and vacuum on the swing side. Medical grade PVC tubing is common for the short patient lead outside the machine, where there is no vacuum and no cleaning cycle.

Is this hose medical grade?

Yes. The compound is platinum-cured silicone supported by FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS documentation, and ISO 10993 biocompatibility reports (cytotoxicity, skin sensitisation, skin irritation) are issued per part on request. The plant runs ISO 9001 and ISO 13485 quality systems.

What pressure does it hold?

Burst is 1.18–3.73 MPa depending on the bore, measured as a minimum on a new hose. Working pressure is the burst figure divided by the safety factor your device qualification uses, and we quote it against that factor rather than publishing one headline number.

Can it take vacuum?

Yes. The braid carries the load instead of the wall, so the bore can be drawn to full vacuum without collapsing — that is the usual reason a concentrator line uses a reinforced hose rather than a plain tube.

Can it be disinfected or sterilised?

The bore is smooth and non-porous, and the hose is rated to 200 °C continuous, so steam sterilisation temperatures sit inside the material range. The cycle itself is validated on the assembled device; tell us the method and the hose is quoted for that duty.

What sizes are available?

Eleven published sections from ID 3 mm to 31.75 mm, each with a burst figure and a bend radius. Concentrator lines usually take ID 3, 4, 5, 6 or 8 mm; other bores are made to order.

Does it add odour or taste to the oxygen?

No. The compound is platinum-cured with no peroxide residue and no plasticiser in the wall, and the hose is odourless, so nothing migrates into the gas stream.

What is the lead time and can I get a sample?

Published sections ship in 5 to 7 working days, and stock samples leave in 3 days. Custom constructions take 10 to 20 working days. Stock samples are free; freight is paid by the buyer.

Need a documented braided silicone hose for a concentrator line?

Send the bore, the pressure or vacuum on the line, the cleaning method and the connector. You get the section, the burst figure, the document list and a sample date back.

Request a quote

WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com

Braided silicone tube for oxygen concentrator
Oxygen concentrator braided silicone hose: a platinum-cured medical grade silicone bore, a polyester braid and an outer jacket bonded into one wall. ISO 10993 reports on request, ISO 13485 and ISO 9001 quality systems, full vacuum, burst 1.18–3.73 MPa by bore, −40 °C to +200 °C, ID 3–31.75 mm published sections.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided silicone tube for oxygen concentrator

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.