Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

External braided silicone tube

External braided silicone tube: a silicone inner tube with a dense braid wound over the outside, so the braid takes the pressure and the abrasion while the fluid only touches silicone. Burst 3–5 MPa, FDA 21 CFR 177.2600 and LFGB silicone, −40 to +200 °C, braid yarn and pattern customizable.

    Product Features

    Two-layer construction: a silicone inner tube with a dense braid wound directly over it
    The braid carries the pressure load, limits expansion under pressure and protects the silicone core from abrasion
    Burst pressure 3–5 MPa, between a normal braided silicone hose and a steel-wire or mesh-fabric reinforced hose
    Holds its bore while staying flexible, so the tube can be routed without collapsing the core
    FDA- and LFGB-compliant silicone, specified for food-grade lines
    Braid yarn and braid pattern customizable, so coverage and surface texture can be matched to the application

    Application

    Food-grade production lines
    Silicone contact surfaces on equipment that handles food and beverages.
    Coffee machines
    The typical case: water and hot-water lines inside the machine.
    Washing machines with heating
    Heated washer lines, where temperature and pressure apply at the same time.
    Medium-pressure service
    Where a normal braided hose has too little headroom and wire reinforcement is more than needed.
    OEM braid customization
    Braid yarn, coverage and pattern specified per project for private-label builds.
    Custom lengths and coils
    Cut-to-length runs or continuous coils, matched to how the line is assembled.

  • Parameters

    Product Features

    Two-layer construction: a silicone inner tube with a dense braid wound directly over it
    The braid carries the pressure load, limits expansion under pressure and protects the silicone core from abrasion
    Burst pressure 3–5 MPa, between a normal braided silicone hose and a steel-wire or mesh-fabric reinforced hose
    Holds its bore while staying flexible, so the tube can be routed without collapsing the core
    FDA- and LFGB-compliant silicone, specified for food-grade lines
    Braid yarn and braid pattern customizable, so coverage and surface texture can be matched to the application

    Application

    Food-grade production lines
    Silicone contact surfaces on equipment that handles food and beverages.
    Coffee machines
    The typical case: water and hot-water lines inside the machine.
    Washing machines with heating
    Heated washer lines, where temperature and pressure apply at the same time.
    Medium-pressure service
    Where a normal braided hose has too little headroom and wire reinforcement is more than needed.
    OEM braid customization
    Braid yarn, coverage and pattern specified per project for private-label builds.
    Custom lengths and coils
    Cut-to-length runs or continuous coils, matched to how the line is assembled.
Yutian · food-grade · external braid · silicone tube

The braid sits on the outside, so the product side stays clean silicone

An external braided silicone tube is a two-layer build: a silicone inner tube with a dense braid wound over it. The braid is the outer surface, so it takes the abrasion and carries the hoop load, while the bore stays silicone — the only surface the fluid touches. Burst pressure is 3–5 MPa, and the silicone is documented to FDA 21 CFR 177.2600 and LFGB.

Burst 3–5 MPaFDA & LFGB siliconeCustom braid yarn & patternFood-grade lines−40 °C to +200 °C

What the two layers each do

The inner tube is the functional layer. It holds the fluid, keeps the bore smooth and non-porous, and brings the chemical resistance that silicone is chosen for in the first place. Wall thickness is set by the bore and the pressure, not by the braid.

The braid is the structural layer. Wound directly over the tube, it takes the hoop load the pressure puts into the wall, limits how far the tube can expand before it starts to creep, and shields the silicone from the chafe of a panel edge, a bracket or another line in the same cabinet. Braid angle and coverage are what decide how much of that load the braid really carries.

There is no outer silicone jacket in this construction — that is the difference from an internal braided hose, where the braid is buried between two silicone layers and the outside is a smooth silicone skin. Here the braid is exposed, which is exactly what makes it the right part for a line that rubs, and the wrong part for a line whose outside has to be wiped down to a cosmetic standard. Both builds are made here, and both are described on the braided silicone hose range.

Where it sits in the pressure range

Burst pressure is 3–5 MPa, depending on the bore and the braid. That places the construction between a normal braided silicone hose and a steel-wire or mesh-fabric reinforced hose: clearly more headroom than a normal braid, without the stiffness, the weight and the coupling cost that wire reinforcement brings.

Burst is the figure published on this page. Working pressure is not a single number on any hose — it is the burst figure divided by the safety factor your application works to, 4:1 for a general duty line and 3:1 where a shorter service interval is accepted. Tell us the factor and the bore, and the working pressure is quoted against it rather than guessed at here.

Two things raise the burst number in practice, and both are settable: the braid coverage (how much of the tube the yarn covers per wind) and the yarn itself. A denser braid in a stronger yarn carries more before the wall yields.

External braid, normal braid or wire reinforcement?

The three constructions answer three different questions. A normal braided hose puts a jacket over the braid and gives you a smooth, wipeable outside. A steel-wire or mesh-fabric hose moves the reinforcement up a class and accepts the stiffness that comes with it. An external braid keeps the pressure headroom of a braid and puts it on the outside, where it also does the abrasion work.

PropertyExternal braid (this tube)Normal braided hoseSteel-wire / mesh hose
Braid positionOutside, exposedUnder an outer silicone jacketOutside or between layers
Burst headroom3–5 MPaLowerHigher
Outside surfaceTextile braidSmooth silicone skinWire or fabric mesh
AbrasionThe braid takes the wear instead of the wallThe jacket takes the wearThe reinforcement takes the wear
FlexibilityFlexible, tight bends in a cabinetFlexible, smooth routingStiffer, larger bend radius
Cleaning the outsideWipe and dry the braidWipeable silicone skinDepends on the build
Fluid contactSilicone bore onlySilicone bore onlySilicone bore only

The braid itself — how it is wound and what it does to the bore — is worked through in how a braided silicone hose is built. For the hotter end of the range, see the braided silicone steam hose, and for the double-layer mesh build, the mesh reinforced silicone hose.

Food-grade, stated as documents

The silicone layer is documented for food contact to FDA 21 CFR 177.2600 and LFGB, with REACH and RoHS declarations covering the European market. The plant runs ISO 9001 and ISO 13485 quality systems, and batches are traceable from compound to finished coil.

Food-grade is a question of what is in the wall and what can come out of it, and the geometry of an external braid helps on both counts: the braid never enters the fluid path, and the product only ever touches a continuous silicone bore. There is no adhesive or bonding layer between the fluid and the wall in this construction — the braid is wound over the tube, not laminated into it.

What we do not do is borrow a claim from another construction. The compliance statement on a quotation names the documents issued for the part you are buying, and the tests are arranged per project when your specification needs a report rather than a declaration.

Where this tube is used

Coffee machines

Water and hot-water lines inside the machine, where the braid survives a tight cabinet and the bore stays silicone.

Washing machines with heating

Heated washer lines: the braid holds the tube against pressure while the silicone takes the temperature.

Food-grade production lines

Fluid lines on food and beverage equipment, where the contact surface has to be a documented silicone.

Water and steam lines in appliances

Appliance builds where a plain silicone tube would balloon, chafe or flatten against a panel edge.

OEM braid customization

Braid yarn, coverage and pattern set per project, so the finished outside matches the drawing the machine was designed around.

Maintenance and aftermarket

Cut lengths and coils matched to the bore and braid of the part being replaced, without a minimum run of moulded parts.

What you can specify

Bore and wall

Built to the drawing. The braid is wound onto the tube you specify, so the bore is not locked to a fixed table of sections.

Braid yarn

Polyester for the general case, aramid where the line runs hot, cotton or nylon where the duty calls for them. The yarn is chosen with the temperature and the abrasion in mind.

Braid pattern

Braid angle and coverage are set at the winder, which changes both the pressure headroom and the texture of the finished outside.

Length and ends

Cut to length or coiled, with bare ends for your own connector. Where an assembly is needed, non-silicone fittings are integrated through partner manufacturers — we make the silicone part.

Documentation

Material certificates with the shipment, FDA and LFGB statements, REACH and RoHS declarations, and third-party testing arranged per project.

Packing

Coils, spools or straight lengths, labelled per line item so a production cell can pull the right part without measuring.

Three affiliated companies, one silicone chain

The tube is the last step of a chain controlled from the compound up: raw material, compounding and the finished hose are handled by three affiliated companies, and Yutian ships the hose you buy.

Guilin Yutian New Materials

Silicone raw material and compound development, 28,000 m² site.

Dongguan Huahong Rubber and Plastic

Compounding, auxiliaries and batch control before extrusion.

Dongguan Yutian Silicone

Extrusion, braiding and finishing in a 6,800 m² plant.

Lead time, samples and tooling

Standard bores

Ship in 5 to 7 working days from stock compounds.

Samples

Stock samples leave in 3 days and are free; freight is paid by the buyer.

Custom construction

10 to 20 working days, depending on the yarn and the braid pattern.

Tooling

Standard bores run on existing tooling; only a bore or braid outside the usual range is quoted as a construction change, because the braid is wound onto the tube rather than moulded around it.

Documents, cleanroom and the limits worth stating

Production runs on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, at a monthly capacity of up to 8 million metres, since 2012.

The limits, stated on the page rather than left to a footnote: the tube is not for human implantation, it is not a breathing-circuit tube for long-term ventilator use, and it does not replace validation of the assembled line. The braid is a textile surface — if your cleaning procedure needs a smooth, wipeable outside, a jacketed braided hose is the better fit, and we make that too.

Working pressure is quoted per project against your safety factor. Nothing on this page is a substitute for the drawing and the material certificate that come with the order.

Questions buyers ask before they specify

Is outer braided silicone tubing the same as external braided silicone tube?

Yes. Both describe the same two-layer construction: a silicone inner tube with a braid wound over the outside. “Outer” and “external” refer to where the braid sits; catalogues also call it overbraided silicone tubing.

Is 3–5 MPa the working pressure?

No. 3–5 MPa is the burst pressure. Working pressure is the burst figure divided by the safety factor your application uses — 4:1 for a general line, 3:1 where a shorter service interval is accepted — so it is quoted per project rather than published as one number.

Is it food-grade?

The silicone bore is documented to FDA 21 CFR 177.2600 and LFGB, with REACH and RoHS declarations. The braid sits outside the fluid path, so the product only touches silicone.

Can it be used in a coffee machine?

Yes, that is the typical case: water and hot-water lines inside the machine, where the hose is routed around a pump, a boiler or a cabinet edge and the outside has to survive the chafe.

Will it take the heat of a washing machine?

The hose is rated −40 °C to +200 °C continuous, which covers heated washer lines. Tell us the water temperature and the pressure cycle and the construction is matched to them.

Can the braid be customized?

Yes. The yarn, the braid angle and the coverage are all set at the winder, so both the pressure headroom and the surface texture of the finished tube can be matched to the drawing.

What sizes do you make?

Bores are built to the drawing rather than limited to a fixed list — the braid is wound onto the tube you specify. The published sections of the standard braided range are on the braided silicone hose page.

What is the lead time, and can I get a sample?

Standard bores ship in 5 to 7 working days, stock samples leave in 3 days, and a custom construction takes 10 to 20 working days. Stock samples are free; freight is paid by the buyer.

Need an external braided tube for a food-grade line?

Send the bore, the working pressure and the safety factor, the temperature, and the braid you want. You get the section, the burst figure, the document list and a sample date back.

Request a quote

WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com

External braided silicone tube
External braided silicone tube: a silicone inner tube with a dense braid wound over the outside, so the braid takes the pressure and the abrasion while the fluid only touches silicone. Burst 3–5 MPa, FDA 21 CFR 177.2600 and LFGB silicone, −40 to +200 °C, braid yarn and pattern customizable.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

External braided silicone tube

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.