Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided silicone tube for coffee machine

Braided silicone tube for coffee machines: a food-grade silicone bore, a polyester braid and an outer silicone skin. Pump-to-brew-head runs at 9 bar, steam runs at 125–150 °C, sections from 3 × 8 to 5 × 11 mm, FDA 21 CFR 177.2600 and LFGB silicone, working pressure quoted per segment.

    Product Features

    Three-layer sealed build — food-grade silicone bore, polyester braid, and a silicone outer skin that keeps the yarn away from moisture, cleaner and the cut edge
    Braided for pulsed pressure — the braid takes the hoop load from a vibration pump, so the bore keeps its diameter and the shot stops drifting
    Working pressure quoted per segment — 0.8 MPa for inlet and drain runs, 1.5 MPa for pump and brew runs, both reduced by about 1% for every degree above 100 °C
    Sections machine builders already use — 3 × 8, 4 × 8, 4 × 9 and 5 × 11 mm, plus custom bore and wall up to 20 mm ID
    Food-contact documents, not slogans — FDA 21 CFR 177.2600, LFGB, REACH and RoHS statements with the shipment; product-level testing arranged per project
    Cut, coiled and packed per line item — bare ends for your own barb or clamp, with the length and tolerance on the label

    Application

    Pump to brew head
    The high-pressure run behind the pump, where pulsed output has to be absorbed.
    Boiler and hot-water lines
    Short braided sections from the boiler or thermoblock to the valve group.
    Espresso and capsule machines
    Home and office machines where the cabinet is tight and the bends are many.
    Commercial machines
    Café and restaurant brew and hot-water mains, where the pump duty is continuous.
    Automatic milk circuits
    Lines that see a daily hot wash as well as pump pressure.
    Replacement and service parts
    Cut lengths matched to the original part, with the same section and braid.

  • Parameters

    Product Features

    Three-layer sealed build — food-grade silicone bore, polyester braid, and a silicone outer skin that keeps the yarn away from moisture, cleaner and the cut edge
    Braided for pulsed pressure — the braid takes the hoop load from a vibration pump, so the bore keeps its diameter and the shot stops drifting
    Working pressure quoted per segment — 0.8 MPa for inlet and drain runs, 1.5 MPa for pump and brew runs, both reduced by about 1% for every degree above 100 °C
    Sections machine builders already use — 3 × 8, 4 × 8, 4 × 9 and 5 × 11 mm, plus custom bore and wall up to 20 mm ID
    Food-contact documents, not slogans — FDA 21 CFR 177.2600, LFGB, REACH and RoHS statements with the shipment; product-level testing arranged per project
    Cut, coiled and packed per line item — bare ends for your own barb or clamp, with the length and tolerance on the label

    Application

    Pump to brew head
    The high-pressure run behind the pump, where pulsed output has to be absorbed.
    Boiler and hot-water lines
    Short braided sections from the boiler or thermoblock to the valve group.
    Espresso and capsule machines
    Home and office machines where the cabinet is tight and the bends are many.
    Commercial machines
    Café and restaurant brew and hot-water mains, where the pump duty is continuous.
    Automatic milk circuits
    Lines that see a daily hot wash as well as pump pressure.
    Replacement and service parts
    Cut lengths matched to the original part, with the same section and braid.
Yutian · coffee machine · braided silicone tube · three-layer

Not every line in a coffee machine needs a braid — but the pump side does

A vibration pump delivers pressure in pulses. Each pulse stretches the wall a little and lets it spring back, and after a few thousand cycles the bore has grown: the same shot time then gives more water, and extraction drifts. The braid holds the bore where it was extruded.

Pump-to-brew-head braid3 × 8 to 5 × 11 mmFDA 21 CFR 177.2600 & LFGB−40 °C to +200 °CCustom sections

Which lines inside a coffee machine need the braid

The split is by function, not by the price of the machine. From tank to cup an espresso machine is five runs, and only the first three are worth a braid.

RunTypical conditionBraid?What decides it
Pump outlet → boiler / brew head9 bar at the puck, 10–12 bar behind the pumpYesPulsed pressure plus a thin wall; the run that decides shot consistency.
Steam valve → steam wand1.0–1.5 bar, 125–150 °CUsuallyPressure is low, but the wand is bent all day; braid resists collapse at the bend.
Mains water → pump2–4 bar, sometimes under suctionOptionalOnly where the route is tight or the pump pulls a vacuum on the inlet.
Drain, OPV return, expansionClose to tank pressureNoA braid adds nothing here and hides the flow a technician needs to see.
Milk circuit / CIP loopPump pressure plus a daily hot washUsuallyCleaner, pressure and repeated flexing together; the bore has to stay round.

Why the pump-to-brew-head run has to be braided

Catalogue copy usually stops at "the braid raises the pressure rating", which is the least interesting thing it does. Unbraided silicone of 1.5–2 mm wall takes the pressure easily. What it does not take unchanged is the cycling: the bore creeps outward, flow resistance drops, and the wall thins at each bend until one of those spots fails.

The braid moves that hoop load into the yarn, so the bore stays at its extruded diameter and the same grind keeps giving the same yield. Dimensional stability is why it sits on this run; pressure resistance is the side effect. A thicker wall is the other way to buy pressure, and it stiffens the tube too — tighter bends and more assembly force in a compact cabinet.

Three layers, and what each one is doing

Inner — food-grade silicone

The only surface the coffee touches. Smooth bore, no taste carried into the cup, and the thickness that sets the pressure rating.

Middle — braid

Wound at a controlled angle and coverage. Takes hoop stress off the silicone and limits radial growth under pulsing.

Outer — silicone skin

Seals the yarn away from moisture, cleaner and hot air, stops it fraying at the cut, and gives service a wipeable outside.

The outer skin is the layer dropped to save cost. Without it the yarn takes up water and cleaner and leaves loose filament when the tube is cut. A two-layer tube with exposed braid is a valid product — see the external braided silicone tube — but the run behind a coffee pump is a sealed three-layer part.

The sections that actually turn up in coffee machines

Section (ID × OD)WallWhere it is usedNote
3 × 8 mm2.5 mmCapsule machines, small-bore brew and steam linesSmall bore carries more pressure per unit of wall area.
4 × 8 mm2.0 mmMost common: brew and hot-water main lineThe baseline section in European machines.
4 × 9 mm2.5 mmSame bore where pressure headroom matters moreSame ID as 4 × 8 — a wall choice, not a different bore.
5 × 11 mm3.0 mmCommercial brew and hot-water mainsMore flow, stiffer; check the bend radius before choosing.

4 × 8 is the de facto baseline

Four millimetre bore, 8 mm outside, is the section most European machines are drawn around, and what a replacement part usually turns out to be. Send a sample with no drawing and the odds are good it is 4 × 8.

Metric and inch are two different systems

1/4 inch is 6.35 mm, not 4 mm; 4 × 8 has no inch equivalent, the nearest being 5/32 inch at 3.97 mm. 5/16 inch is 7.94 mm and 3/8 inch is 9.53 mm. Ask which market the drawing came from before quoting.

4 × 8 or 4 × 9, and how big the bore should be

Both are 4 mm bore: 4 × 9 gives more pressure headroom and less flex, 4 × 8 bends more easily in a crowded cabinet. A single espresso runs at about 1.5–2 ml/s, which a 4 mm bore at 9 bar carries comfortably; going bigger adds retained liquid and wetted wall.

Pressure and temperature: three numbers that are not the same number

Point in the circuitbarMPaTemperature
Brew head, at the puck9 bar0.9 MPa90–96 °C
Vibration pump, rated peak15–19 bar1.5–1.9 MPacold side
Behind the pump, after the OPV10–12 bar1.0–1.2 MPahot side
Steam boiler1.0–1.5 bar0.10–0.15 MPa125–150 °C
Mains water inlet2–4 bar0.2–0.4 MPaambient

Three different figures, and a tube only sees the one at its own position. That is why a single "working pressure 0.8 MPa" on a data sheet is a warning sign: it covers the inlet and the drain, and sits below what the run behind the pump meets on every shot.

How the working pressure is quoted here

Per segment, at working temperature: at least 0.8 MPa for inlet and drain, at least 1.5 MPa for pump and brew runs, both derated for temperature. Working pressure is not a property of a tube on its own — it is burst divided by the safety factor the machine is designed to, 4:1 for a general line and 3:1 where a shorter service interval is accepted.

Derating, and why the burst figure is not a race

Above 100 °C the rating drops by about 1% per degree. The steam run sits at 125–150 °C, so its usable rating is calculated at that temperature. A polyester braid typically bursts at three to four times its working pressure; for coffee runs 2.5–3.0 MPa is the sensible published window, and past 4.5 MPa the lost flexibility returns as assembly stress.

What the food-contact paperwork actually says

Two different things get called "FDA". One is a material declaration: the compound documented against FDA 21 CFR 177.2600, the clause for rubber in repeated food contact. The other is a product test report on the finished tube — a specific bore, wall and braid, tested at a specific temperature against a specific food simulant. A builder working towards a unit certificate needs the second; a purchasing team checking a supplier usually asks for the first. Say which one your file needs at quotation.

FDA 21 CFR 177.2600 and LFGB

US repeated-use rubber clause, plus German food-contact law with sensory testing of odour and taste transfer under (EU) 1935/2004.

REACH and RoHS

Substance restrictions for the European market and the electrical parts around the tube; SVHC declarations on request.

NSF/ANSI 51 and 61

51 covers food-equipment materials, 61 drinking-water components. If your machine holds one of them, say which — they are not the same test.

When a braided tube is the wrong choice

Four cases where the braid costs money and buys nothing.

You need to watch the flow

Braid is opaque. Where a technician diagnoses by looking for bubbles, scale or discolouration, a clear unreinforced tube works better.

The line runs at tank pressure

Drain, OPV return and expansion lines. A braid adds cost and hides the flow without adding life.

The run is very short

Under about 20 mm the braid adds only stiffness, making assembly harder for no gain.

The milk line is pulled apart daily

Repeated plugging works the cut end, and unsealed filament can reach the milk path.

What you can specify

Bore and wall

Built to the drawing. Standard 3–10 mm ID, up to 20 mm ID as a custom extrusion; wall 2.0–4.0 mm depending on the section.

Yarn, braid angle and coverage

Polyester for most coffee runs, aramid where the line stays hot. Coverage is set at the winder and quoted with the section.

Length and ends

Cut to length or coiled, ends bare for your own barb or clamp. Where an assembly is needed, non-silicone fittings are integrated through partner manufacturers — we make the silicone part.

Documentation and packing

Material certificates with the shipment, FDA and LFGB statements, REACH and RoHS declarations, third-party testing per project; bags, spools or boxed lengths labelled per line item.

Where the tube is made

The tube is the last step of a chain controlled from the compound up: Guilin Yutian New Materials (compound, 28,000 m²), Dongguan Huahong Rubber and Plastic (compounding and batch control) and Dongguan Yutian Silicone (extrusion, braiding and finishing, 6,800 m²).

Production runs on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, up to 8 million metres a month, since 2012. Limits worth stating: not for human implantation, and not a substitute for validation of the assembled machine.

Send these ten numbers and the quote comes back once

Most enquiries take four or five rounds because the drawing and the duty are not in the first message. This list usually does it in one.

What we needWhat to sendWhy it matters
Machine and positionBrand, model, and where in the circuit the tube sitsSets temperature, pressure and whether steam is involved.
SectionID × OD, or ID plus wall; say whether the drawing is metric or inch1/4 inch is 6.35 mm, not 4 mm.
PressureWorking pressure and peak (pulse) pressureThe peak is what fatigues the wall.
TemperatureContinuous and peak, plus whether steam is presentNeeded for the derating calculation.
MediumDrinking water, coffee, steam, milk, cleaner (with chemistry)Drives the compound and the test plan.
Structure and yarnThree-layer sealed braid or exposed braid; polyester or aramidChanges both the process and the price.
EndsBarb size, insertion length, clamp type and widthMost leaks and pull-offs happen at the end.
Length and quantityCut length, tolerance, annual and per-release volumeSets the cutting and packing method.
DocumentationMaterial statement or product test report; target marketThe two are quoted differently.
RoutingSmallest bend radius and the space around the tubeDecides 4 × 8 against 4 × 9.

Without all of it, send a photo of the original tube, the machine model and the position. Standard sections ship in 5 to 7 working days, stock samples in 3 days, custom construction in 10 to 20 working days.

Questions buyers ask before they specify

Does the braid make the tube stiff?

It raises the bending force, and how much depends on the wall rather than the braid: the 4 × 8 routes more easily than the 4 × 9, which is why the thinner wall is the usual choice in a compact cabinet.

Can a thicker unbraided tube replace it?

Under static pressure yes. Behind a vibration pump no: a thicker wall raises the burst figure but does not stop the bore creeping under pulsing, so the flow still drifts.

Is a higher burst pressure better?

No. Past what the machine needs, extra burst means a thicker wall or denser braid, and the flexibility given up shows up as assembly stress. For coffee runs 2.5–3.0 MPa is the practical window.

What is different about the steam run?

Three things: above 130 °C the compound should be platinum-cured, the rating is derated by 1% per degree above 100 °C, and only a steam-rated tube should be used — a hot-water rating is not a steam rating.

Why are some tubes in the same machine clear?

Those runs sit at tank pressure or need to be watched. Builders mix the two on purpose: braid where the pump pushes, clear tube where a technician has to see the flow.

What about lead time and samples?

Standard sections ship in 5 to 7 working days, stock samples in 3 days with freight paid by the buyer, and a custom construction takes 10 to 20 working days.

Need a braided tube for a coffee machine line?

Send the machine model, the section and the position in the circuit. You get the section review, the pressure figure for that run and a sample date back.

Request a quote

WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com

Braided silicone tube for coffee machine
Braided silicone tube for coffee machines: a food-grade silicone bore, a polyester braid and an outer silicone skin. Pump-to-brew-head runs at 9 bar, steam runs at 125–150 °C, sections from 3 × 8 to 5 × 11 mm, FDA 21 CFR 177.2600 and LFGB silicone, working pressure quoted per segment.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided silicone tube for coffee machine

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.