Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided Silicone Tubes for Ice Makers

Braided silicone tube for ice makers: an inner-braid three-layer build (food-grade silicone bore, braid, silicone skin) that keeps a 2.0 mm wall from collapsing on the pump suction line. ID 4–12 mm common, −40 to +200 °C, working pressure quoted per section against the safety factor, NSF/ANSI 51 and FDA 21 CFR 177.2600 materials.

    Product Features

    Inner braid, three sealed layers — food-grade silicone bore, one braid layer and a silicone outer skin, so the braid never touches the water and the outside stays wipeable
    Braided for the suction side — the braid takes the inward load between reservoir and pump, so a 2.0 mm wall keeps its bore instead of taking a set over thousands of cycles
    Materials documented for food equipment — silicone and colour compound documented to NSF/ANSI 51, with FDA 21 CFR 177.2600 and LFGB statements shipped with the order
    −40 °C to +200 °C continuous — built for cold water and daily wash cycles, with the headroom there for the cleaning step rather than for the process
    Sections ice machine drawings use — 4–5, 6–8, 8–10 and 10–12 mm ID bands; published braided range 3–31.75 mm; wall 2.0–3.0 mm
    Food-grade colour, not pigment on yarn — colour goes in as a silicone compound under the skin, so the odour question that stops an external-braid tube does not arise

    Application

    Pump suction to the evaporator
    Where a thin wall creeps closed and the ice sheet stops forming evenly.
    Water inlet and fill
    Long or tightly routed fills from the building supply to the reservoir or float valve.
    Circulation over the evaporator
    Cold water returning from the evaporator, bent and holding shape all day.
    Commercial ice machines
    Higher duty cycles and longer runs on the same water circuit.
    Glycol and secondary refrigerant
    Propylene glycol loops, and ethylene glycol where the leak path is handled.
    Replacement and service parts
    Cut lengths matched to the part being replaced, same section and braid.

  • Parameters

    Product Features

    Inner braid, three sealed layers — food-grade silicone bore, one braid layer and a silicone outer skin, so the braid never touches the water and the outside stays wipeable
    Braided for the suction side — the braid takes the inward load between reservoir and pump, so a 2.0 mm wall keeps its bore instead of taking a set over thousands of cycles
    Materials documented for food equipment — silicone and colour compound documented to NSF/ANSI 51, with FDA 21 CFR 177.2600 and LFGB statements shipped with the order
    −40 °C to +200 °C continuous — built for cold water and daily wash cycles, with the headroom there for the cleaning step rather than for the process
    Sections ice machine drawings use — 4–5, 6–8, 8–10 and 10–12 mm ID bands; published braided range 3–31.75 mm; wall 2.0–3.0 mm
    Food-grade colour, not pigment on yarn — colour goes in as a silicone compound under the skin, so the odour question that stops an external-braid tube does not arise

    Application

    Pump suction to the evaporator
    Where a thin wall creeps closed and the ice sheet stops forming evenly.
    Water inlet and fill
    Long or tightly routed fills from the building supply to the reservoir or float valve.
    Circulation over the evaporator
    Cold water returning from the evaporator, bent and holding shape all day.
    Commercial ice machines
    Higher duty cycles and longer runs on the same water circuit.
    Glycol and secondary refrigerant
    Propylene glycol loops, and ethylene glycol where the leak path is handled.
    Replacement and service parts
    Cut lengths matched to the part being replaced, same section and braid.
Yutian · ice machine · inner braid · three-layer

In an ice machine the braid is not there for heat — it holds the bore open

An ice machine fills, circulates and drains the same water all day. On the fill and circulation runs the pump pulls more than it pushes, and a thin silicone wall has only its own hardness to stop it closing. This tube puts a braid between the bore and a silicone skin, so the bore keeps the diameter it was extruded at.

Inner braid, 3 layersID 4–12 mm commonNSF/ANSI 51 materials−40 °C to +200 °CCustom sections

What it is, and the three surfaces a buyer should know

Three layers: a food-grade silicone bore, one braid layer wound over it, and a silicone outer skin. No adhesive or bonding layer touches the water — the braid is wound onto the tube, not laminated into it.

Bore — the only wetted surface

Food-grade silicone, smooth and non-porous. Wall thickness follows the bore and the duty.

Braid — what carries the load

Wound at a set angle and coverage; takes the inward pull on suction and the hoop load under pressure.

Skin — what the outside is

Silicone over the braid: keeps yarn away from cleaner and moisture, stops the cut end fraying, and wipes down.

Which lines in an ice machine need the braid

The split is by what the water is doing, not by the price of the machine. Five runs, and only the first three repay a braid. Sections and braid options across the whole range are on the braided silicone hose page.

RunTypical conditionBraid?Why
Water inlet → reservoir or float valvebuilding water, 0.13–0.8 MPaYes, on long or tight runsPressure is low but the run is long; the braid stops the wall ballooning at the joints.
Reservoir → pump → evaporator (suction)below atmosphericYes — the critical oneThe load is inward, and a thin wall creeps closed a little on every cycle.
Circulation return from the evaporator0–5 °C water, low pressureUsuallyCold water and a bend all day; braid resists flattening at the bend.
Drain and overflowtank pressure, open outletNoNothing to resist, and a technician may need to see whether it drains.
Water-cooled condenser feedline pressure, warm sideOptionalOnly where the route collapses or the tube is a structural run.

The suction line is where the braid earns its place

Between reservoir and pump the pressure is below atmospheric for most of the cycle, so every stroke pulls the wall inward. Silicone returns to shape well but not perfectly: over thousands of strokes the bore takes a set, narrows, and the pump moves less water without sounding any different.

What shows up is not a burst. It is ice thin at the end of a sheet and a harvest cycle running past the timer. Three things worth checking on a tube that has been in service:

The bore is not round

Cut a section and hold it against a rule. An oval or a flattened band means the wall was doing the braid's job.

The wall has thinned at a bend

Thinning concentrates at the shortest radius in the cabinet, not on the longest run.

The end has crept off the barb

A tube that has grown under cycling also grows at the joint — a clamp question, not a braid one.

Why an inner braid, and what it does for food-contact documents

Where the braid sits decides two things at once: what the outside of the tube is, and how the colour gets in.

Braid outside

Yarn is the outer surface, so colour goes on as a pigment paste over exposed yarn. Paste carries odour, normally handled with a second vulcanising pass — and odour is what a food-contact review asks about. That is why an external braid build usually cannot carry an NSF statement.

Braid inside — this tube

The braid sits under a silicone skin and the colour goes in as a food-grade silicone compound, not a paste on yarn. No exposed yarn, no paste: the inner-braid construction is the one that can be documented to NSF/ANSI 51 as material for food equipment.

That is a materials statement, not a certificate for the part. Material documents ship with the order, product-level testing is arranged per project, and the certificate for the assembled machine sits with the machine builder.

StandardWhat it coversWhere it sits for this part
NSF/ANSI 12Ice-making equipment (the machine)Not ours to hold — it applies to the builder's product.
NSF/ANSI 51Food equipment materialsThe level our silicone and colour compound are documented against.
NSF/ANSI 61Drinking-water system componentsA different test; relevant only if the line is a potable-water component.

We send FDA 21 CFR 177.2600 and LFGB statements, REACH and RoHS declarations and NSF/ANSI 51 material documentation with the shipment; the plant runs ISO 9001 and ISO 13485, and batches trace from compound to finished coil. The tube is not for human implantation.

Operating conditions, and why cold is the harder problem

The ranges below are what machine builders publish for their own units: a starting point, not a specification of the tube. Quote against the run, not against a machine class.

Point in the circuitTypical figureWhat it means for the tube
Water inlet0.13–0.8 MPa; most machines 0.15–0.5 MPaCity or building pressure, so the fill line is rarely the critical run.
Inlet water temperature5–35 °CCold water, which is why 200 °C of material headroom stays unused.
Circulating water over the evaporator0–5 °CThe coldest continuous duty, and the one that sets the braid choice.
Wash / rinse / sanitise15 / 15 / 25 minutes, repeated dailyShort warm peaks and a chemical load; this ages the tube, not heat.
Pump suction sidebelow atmosphericThe load is inward — not a pressure rating in the usual sense.

Almost every enquiry asks about heat. Almost every failure comes from cycling: cold water on and off with a warm wash between, hundreds of times a month. Freeze-thaw is where a bore changes — water left in a line, a machine standing in an unheated space, a defrost that outruns the drain. The braid is what keeps that load from becoming a permanent change of shape. On the chemical side it is concentration creep and dwell time that shorten life, not the sanitiser at the strength a machine uses.

Sections that turn up in ice machines

Bore is quoted as ID and the wall follows from the duty. Published sections across the braided range run 3 mm to 31.75 mm ID; the four bands below are the ones on ice machine drawings. Where a run needs more headroom than a single braid gives, the double-layer mesh build is the next step up.

Section (ID)Where it turns upNote
4–5 mmSmall under-counter and domestic machines; evaporator in and outThe tight-bend end of the range — check the run before stepping up a size.
6–8 mmThe mainstream: pump suction and water circulationMost replacement parts sit here. A 6 mm bore is not a 1/4 inch line.
8–10 mmCommercial machines with longer runsBending radius decides the wall; check it before stepping down.
10–12 mmDrain and overflow linesUsually the run that does not need a braid at all.

Wall thickness, and why 2.0 mm matters here

Walls across these sections run 2.0–3.0 mm. The thin end is what makes a suction run worth braiding: flexible enough for a small cabinet, thin enough that unbraided it takes a set under a pump. Going thicker instead buys burst strength and loses flexibility, which reappears as assembly stress at the joints.

Metric and inch are two different systems

A 1/4 inch line is 6.35 mm, so a 6 mm bore is not the same part and will not seal the same way on a 1/4 inch barb. The others that come up: 5/32 inch is 3.97 mm, 5/16 inch is 7.94 mm, 3/8 inch is 9.53 mm. Ask which system the drawing came from before quoting — this is the most common mismatch on a replacement order.

Pressure: burst, working pressure and the vacuum side

Burst pressure is quoted per section. Across the published braided range the figures run 1.18–3.73 MPa, and your drawing gets its own number rather than a range.

Working pressure is not a property of the tube on its own: it is the burst figure divided by the safety factor the machine is designed to, 4:1 for general duty and 3:1 where a shorter service interval is accepted. On the suction side the load reverses, so a burst figure says nothing useful — the braid is what resists collapse, and how much a construction takes is quoted per construction. A wall thick enough to resist collapse by itself is also stiff enough to fight a small cabinet.

Where a braided silicone tube is the wrong part

Four cases where the braid costs money and buys nothing:

You need to watch the flow

Braid is opaque. Where a technician diagnoses by looking for bubbles, scale or a slow drain, a clear tube does it better.

The line runs at tank pressure

Drain, overflow and open outlets have nothing to resist; a braid hides the flow without adding life.

The run is very short

Under about 20 mm the braid adds stiffness and makes assembly harder for no gain.

The line is pulled apart every week

Repeated plugging works the cut end; an unbraided tube with a clean cut is the honest choice.

Glycol and brine lines

A secondary refrigerant is chosen for heat transfer, not for taste, so the answers differ from potable water — and in order of how confident we are:

Propylene glycol

Food-grade heat-transfer fluid, common in ice machines. Silicone is compatible; this is the case we support from material data.

Ethylene glycol

Compatible with the silicone, but the fluid is toxic: the tube is fine, the leak path is the risk. Say what the circuit is and the wall is set accordingly.

Calcium chloride / sodium chloride brine

Not recommended without a test on the actual fluid. Chloride finds its way into a cut end; send a brine sample and we run it rather than guess.

What you can specify, and what it is made on

Bore and wall

Built to the drawing, not chosen from a list: wall 2.0–3.0 mm across the ice machine bands.

Braid yarn and coverage

Polyester as standard for cold water, aramid where a line also runs hot; angle and coverage set at the winder.

Colour and ends

Food-grade silicone compound matched to a sample or code, with bare ends for your own barb or clamp; non-silicone fittings are integrated through partner manufacturers — we make the silicone part.

Packing and documentation

Coils, spools or straight lengths labelled per line item, with material statements and declarations in the box.

Where it is made

The tube is the last step of a chain controlled from the compound up: Guilin Yutian New Materials (compound, 28,000 m²), Dongguan Huahong Rubber and Plastic (compounding and batch control) and Dongguan Yutian Silicone (extrusion, braiding and finishing in a 6,800 m² plant) — 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, up to 8 million metres a month, since 2012.

Send six things and the quote comes back once

Most ice machine enquiries take three or four rounds because the drawing and the duty are not in the first message. This list usually does it in one.

What we needWhat to sendWhy it matters
Machine and positionModel, and where in the circuit the tube sitsDecides temperature, pressure and whether the run is under suction
SectionID × OD, or ID plus wall1/4 inch is 6.35 mm, not 6 mm
Water pressureInlet pressure and the pump-side figureAn inlet range and a suction run are not the same specification
Temperature and cleaningWater temperature and the wash / sanitise routineDecides the compound and whether aramid braid is needed
MediumPotable water, glycol, or brine with its chemistryBrine needs a compatibility answer, not an assumption
Length, ends and quantityCut length and tolerance, barb or clamp, per-release volumeSets the cutting and packing method

Without all of it, send a photo of the original tube, the machine model and the position. Standard sections ship in 5 to 7 working days, stock samples in 3 days, a custom construction in 10 to 20 working days; samples are free and freight is paid by the buyer. The same construction questions on the hot side are set out on the coffee machine tube page.

Questions buyers ask before they specify

Does an ice machine need a braided hose at all?

On three runs: inlet, pump suction and the circulation return. On drain and overflow, no — the line sits at tank pressure and an opaque wall only makes a slow drain harder to diagnose.

Why would a silicone tube collapse on the suction side?

The load is inward and a thin wall has only its own hardness to hold the bore. Silicone returns to shape well but not perfectly, so a 2 mm wall takes a set and the flow drops without the pump sounding any different.

What is different about an inner braid?

Where the yarn sits. An external braid is the outer surface, so it takes abrasion and the colour sits on exposed yarn. An inner braid is covered by a silicone skin: wipeable outside, no fraying at the cut, and colour as a food-grade compound.

Can this tube carry an NSF statement?

The silicone and colour compound are documented to NSF/ANSI 51 as materials for food equipment, and the documents ship with the order. That is material level; a product-level report is arranged per project, and the machine certificate sits with the builder.

What temperature does it take?

−40 °C to +200 °C continuous. In an ice machine the interesting end is the cold one: 0–5 °C circulating water and daily wash cycles are what age the tube.

Can it carry glycol or brine?

Propylene glycol we support from material data, ethylene glycol is compatible but toxic, and chloride brines we will not recommend without testing the actual fluid.

Which sections do you keep in stock?

The 6–8 mm band covers most replacement orders. Published sections run 3 mm to 31.75 mm ID, and anything between is made to the drawing.

What about lead time and samples?

Standard sections ship in 5 to 7 working days, stock samples in 3 days, custom construction in 10 to 20 working days. Samples are free; freight is paid by the buyer.

Need an inner-braid tube for an ice machine line?

Send the machine model, the section and the position in the circuit. You get the section review, the burst figure for that run and a sample date back.

Request a quote

WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com

Braided Silicone Tubes for Ice Makers
Braided silicone tube for ice makers: an inner-braid three-layer build (food-grade silicone bore, braid, silicone skin) that keeps a 2.0 mm wall from collapsing on the pump suction line. ID 4–12 mm common, −40 to +200 °C, working pressure quoted per section against the safety factor, NSF/ANSI 51 and FDA 21 CFR 177.2600 materials.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided Silicone Tubes for Ice Makers

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.