Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

APPLICATION


Our silicone products are used in all walks of life

APPLICATION


Our silicone products are used in all walks of life

Application Industry

Clear or Milky White: Choosing Silicone LED Diffuser Opacity

2026-10-28 12:45:44

Click:

“ How opacity is chosen for a silicone LED diffuser: what a milky compound does to the light, what a clear wall keeps, how the mix is set per project, and how to brief the choice. ”

A milky white silicone LED diffuser is an extruded translucent silicone cover in which a scattering phase inside the compound spreads each LED into an even field of light. Clear compound keeps more of the beam travelling straight. The choice is a design decision taken with the strip and the cavity, not a fixed grade.

ManufacturingSince 2012 FPC range4–28 mm Temperature−40 to +200 °C Capacity14 extrusion lines

Should I use clear or milky white silicone for LED diffusion?

The answer follows the viewing distance and the cavity, not a preference. Milky white compound carries a scattering phase that spreads each die into a soft field, which keeps a strip looking continuous when the face is read close up or the channel is shallow. Clear compound keeps more light travelling straight, so the face stays bright and the die pattern readable. Both sit on the same 4–28 mm platform.

Does silicone LED sleeve block too much light?

A sleeve does not block a fixed share of the output; it changes its shape. In a milky compound light is diffused rather than pointed, so the face reads as one band rather than a row of dots. How much it spreads is no catalogue number, because transmittance is adjusted through compound formulation and the sleeve is matched to the strip.

What does a milky white compound do to the light?

Both finishes are platinum-cured silicone extrusions. A milky batch carries a fine scattering phase, so light entering the wall is redirected at each particle boundary and leaves the face at many angles, and the eye receives light from a wide area rather than a point. The phase runs through the full 0.5 mm to 0.6 mm wall.

How is the milky level set for a project?

There is no fixed milkiness value to order against, because the number that matters belongs to the assembly. It starts from what the customer has fixed: the strip, the number and pitch of its dies, and the cavity, with a 2.8 mm inner height and an inner width of 8.8 mm to 13 mm. The scattering phase is then adjusted until the dies stop resolving, and the mix is set per project.

What decides whether the LED dots disappear?

Three variables decide it together, and the compound is the third. The first is the strip: its efficacy and the number and pitch of the dies, because closely spaced low-output dies even out more easily. The second is the distance from the board to the emitting face, set by cavity depth, which is 2.8 mm inner height on the stocked bodies. The third is the sleeve's transmittance. That is why the width check against 8 mm, 10 mm and 12 mm strips comes before opacity.

Which side of the trade-off fits my strip and cavity?

The two finishes are not grades of the same thing. One shapes the light, the other lets it pass, and the table maps each to what the strip and the cavity are already doing.

Point of comparison Clear compound Milky white compound
How the emitting face reads Bright and glass-like; dies stay readable An even band; light is diffused, not pointed
Die pitch it suits Wide die pitch, or distant viewing Close die pitch and close viewing
Cavity depth it suits A deep channel that already spreads light A shallow channel at 2.8 mm inner height, where the sleeve spreads
When to choose it Output through the wall drives the design A continuous line with no readable die

Once the strip and cavity are settled, the compound is chosen on a sample: request a matched sample pair and send the strip width, the die pitch and the cavity depth.

Can a grid or a mesh change how the light reads?

A second way to break up the source is geometric rather than chemical. Where a darker strand is co-extruded into the face as a grid, light passes through the openings between the strands, and the face reads as a fine texture on a strip with wide die pitch. The tri-color co-extruded grid-pattern sleeve works that way, and the compound behind it is still chosen for the strip.

Frequently asked questions

Does silicone yellow over time with LED heat?

The compound is resistant to yellowing under normal LED operating temperatures, and long-term use does not embrittle or crack the wall. A clear sleeve shows any colour shift earlier because the face is read directly, while a milky face hides it better. No service life is stated, because it depends on junction temperature and drive current.

What temperature can a silicone LED diffuser withstand?

The extrusion is rated for −40 °C to +200 °C, so a strip running warm does not soften the body. Hardness is 70 ± 5 Shore A, tensile strength is at least 8 MPa and tear strength at least 30 kN/m, which keeps the wall in shape against a clip.

Can a milky white diffuser be made for a 12 mm strip?

Yes. PCB widths of 8, 10 and 12 mm are stocked, and the same structure covers FPC from 4 mm to 28 mm, with an inner width of 8.8 mm to 13 mm and an inner height of 2.8 mm. The compound is set at the same time as the section.

Why can I still see individual LEDs through a diffuser?

Because the sleeve is only one of three variables. Die count and pitch, the distance from the board to the emitting face, and the transmittance of the sleeve all act together; if the cavity is shallow or the dies are widely spaced, no compound can hide them on its own.

What do I send so the compound can be matched to my strip?

Send the strip width, the die pitch, the cavity depth and the run length. Orders are taken against a USD 500 minimum value rather than a minimum length. A stocked item is out in 5 to 7 working days, a sample already in stock in 3, and a new section in 10 to 20.

Related reading

Next step

Send the strip width, the die pitch, the cavity depth and the run length, and say which way the design leans. Roll length follows the body: 200 m for square, grooved and D sections, 100 m for channel covers. ROHS, REACH and UL94 HB sit at material level, and a test report on a finished part is a separate project.

Ready to settle clear or milky?

Send the strip, the cavity and the run length. The compound is proposed against your strip, not a catalogue figure, and the section stays the same.

Request a quote → WhatsApp +8618028921514

DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Clear or Milky White: Choosing Silicone LED Diffuser Opacity

Author:DongGuan Yutian Silicone Rubber Technology Co.,Ltd

A milky white silicone LED diffuser is an extruded translucent silicone cover in which a scattering phase inside the compound spreads each LED into an even field of light. Clear compound keeps more of the beam travelling straight. The choice is a design decision taken with the strip and the cavity, not a fixed grade.

ManufacturingSince 2012 FPC range4–28 mm Temperature−40 to +200 °C Capacity14 extrusion lines

Should I use clear or milky white silicone for LED diffusion?

The answer follows the viewing distance and the cavity, not a preference. Milky white compound carries a scattering phase that spreads each die into a soft field, which keeps a strip looking continuous when the face is read close up or the channel is shallow. Clear compound keeps more light travelling straight, so the face stays bright and the die pattern readable. Both sit on the same 4–28 mm platform.

Does silicone LED sleeve block too much light?

A sleeve does not block a fixed share of the output; it changes its shape. In a milky compound light is diffused rather than pointed, so the face reads as one band rather than a row of dots. How much it spreads is no catalogue number, because transmittance is adjusted through compound formulation and the sleeve is matched to the strip.

What does a milky white compound do to the light?

Both finishes are platinum-cured silicone extrusions. A milky batch carries a fine scattering phase, so light entering the wall is redirected at each particle boundary and leaves the face at many angles, and the eye receives light from a wide area rather than a point. The phase runs through the full 0.5 mm to 0.6 mm wall.

How is the milky level set for a project?

There is no fixed milkiness value to order against, because the number that matters belongs to the assembly. It starts from what the customer has fixed: the strip, the number and pitch of its dies, and the cavity, with a 2.8 mm inner height and an inner width of 8.8 mm to 13 mm. The scattering phase is then adjusted until the dies stop resolving, and the mix is set per project.

What decides whether the LED dots disappear?

Three variables decide it together, and the compound is the third. The first is the strip: its efficacy and the number and pitch of the dies, because closely spaced low-output dies even out more easily. The second is the distance from the board to the emitting face, set by cavity depth, which is 2.8 mm inner height on the stocked bodies. The third is the sleeve's transmittance. That is why the width check against 8 mm, 10 mm and 12 mm strips comes before opacity.

Which side of the trade-off fits my strip and cavity?

The two finishes are not grades of the same thing. One shapes the light, the other lets it pass, and the table maps each to what the strip and the cavity are already doing.

Point of comparison Clear compound Milky white compound
How the emitting face reads Bright and glass-like; dies stay readable An even band; light is diffused, not pointed
Die pitch it suits Wide die pitch, or distant viewing Close die pitch and close viewing
Cavity depth it suits A deep channel that already spreads light A shallow channel at 2.8 mm inner height, where the sleeve spreads
When to choose it Output through the wall drives the design A continuous line with no readable die

Once the strip and cavity are settled, the compound is chosen on a sample: request a matched sample pair and send the strip width, the die pitch and the cavity depth.

Can a grid or a mesh change how the light reads?

A second way to break up the source is geometric rather than chemical. Where a darker strand is co-extruded into the face as a grid, light passes through the openings between the strands, and the face reads as a fine texture on a strip with wide die pitch. The tri-color co-extruded grid-pattern sleeve works that way, and the compound behind it is still chosen for the strip.

Frequently asked questions

Does silicone yellow over time with LED heat?

The compound is resistant to yellowing under normal LED operating temperatures, and long-term use does not embrittle or crack the wall. A clear sleeve shows any colour shift earlier because the face is read directly, while a milky face hides it better. No service life is stated, because it depends on junction temperature and drive current.

What temperature can a silicone LED diffuser withstand?

The extrusion is rated for −40 °C to +200 °C, so a strip running warm does not soften the body. Hardness is 70 ± 5 Shore A, tensile strength is at least 8 MPa and tear strength at least 30 kN/m, which keeps the wall in shape against a clip.

Can a milky white diffuser be made for a 12 mm strip?

Yes. PCB widths of 8, 10 and 12 mm are stocked, and the same structure covers FPC from 4 mm to 28 mm, with an inner width of 8.8 mm to 13 mm and an inner height of 2.8 mm. The compound is set at the same time as the section.

Why can I still see individual LEDs through a diffuser?

Because the sleeve is only one of three variables. Die count and pitch, the distance from the board to the emitting face, and the transmittance of the sleeve all act together; if the cavity is shallow or the dies are widely spaced, no compound can hide them on its own.

What do I send so the compound can be matched to my strip?

Send the strip width, the die pitch, the cavity depth and the run length. Orders are taken against a USD 500 minimum value rather than a minimum length. A stocked item is out in 5 to 7 working days, a sample already in stock in 3, and a new section in 10 to 20.

Related reading

Next step

Send the strip width, the die pitch, the cavity depth and the run length, and say which way the design leans. Roll length follows the body: 200 m for square, grooved and D sections, 100 m for channel covers. ROHS, REACH and UL94 HB sit at material level, and a test report on a finished part is a separate project.

Ready to settle clear or milky?

Send the strip, the cavity and the run length. The compound is proposed against your strip, not a catalogue figure, and the section stays the same.

Request a quote → WhatsApp +8618028921514

DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.

Clear or Milky White: Choosing Silicone LED Diffuser Opacity
How opacity is chosen for a silicone LED diffuser: what a milky compound does to the light, what a clear wall keeps, how the mix is set per project, and how to brief the choice.
Long by picture save/share
0

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Products Recommended

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

CONTACT


Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

 

  • Mobile:
  • 0086-18028921514
  • Fax:0086-769-82555312
  • Email:salesmanager@yutiansilicone.com

Link: China Edge-lit Lighting, Backlight Lighting Manufa

Contact Us

Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

 

  • Mobile/Whatsapp:
    0086-18028921514
  • Fax:86-769-89221009
  • Email:salesmanager@yutiansilicone.com

 

Copyright © 2015-2026 All Rights Reserved.

Copyright © 2015-2026 All Rights Reserved.   

Service Center

Please choose online customer service to communicate

Contacts
Phone
+8618028921514
Service time
From Monday to Sunday
E-mail
salesmanager@yutiansilicone.com
Scan a QR Code
Qrcode
WhatsApp
Add WeChat friend to learn more about the product
Use Enterprise WeChat
"Scan" to join the group chat
Copy success!
Add WeChat friend to learn more about the product
I see.