Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Silicone foam tubing

Silicone foam tubing is extruded from silicone compound with a foaming agent, so the wall is light, compressible and thermally insulating. Supplied in −40 to +200 °C grades, 0.2–1.0 g/cm³ density and 15–70 Shore C hardness, cut to length or coiled. Colour, bore and wall are built to the drawing.

    Product Features

    Extruded silicone foam: wall 0.2–1.0 ±0.1 g/cm³, hardness 15–70 ±5 Shore C
    Smooth non-porous silicone bore, so the inside behaves like a solid silicone tube
    Thermal conductivity ≤0.1 W/(m·K): insulation and thermal break in one part
    Continuous −40 °C to +200 °C, with a 300 °C grade quoted as a custom compound
    Compression set ≤12% at 25%, so a clamped pad returns to its free thickness
    Sections 1–100 mm: round tube, D-shape, strip or sheet, cut to length or coiled

    Application

    Cushioning and clamping
    Pads, sleeves and strips that hold a part without marking it.
    Thermal break
    Sleeving over hot-water and chilled lines, and at clamp points.
    Vibration and noise
    Mounts and spacers under panels, pumps and compressors.
    Dust and water sealing
    Compressible strips and gaskets on enclosures and panel edges.
    Weight reduction
    A foamed section in place of a solid one, at the same envelope.
    Handles and grips
    Soft-touch sleeves and covers on equipment that is handled daily.

  • Parameters

    Product Features

    Extruded silicone foam: wall 0.2–1.0 ±0.1 g/cm³, hardness 15–70 ±5 Shore C
    Smooth non-porous silicone bore, so the inside behaves like a solid silicone tube
    Thermal conductivity ≤0.1 W/(m·K): insulation and thermal break in one part
    Continuous −40 °C to +200 °C, with a 300 °C grade quoted as a custom compound
    Compression set ≤12% at 25%, so a clamped pad returns to its free thickness
    Sections 1–100 mm: round tube, D-shape, strip or sheet, cut to length or coiled

    Application

    Cushioning and clamping
    Pads, sleeves and strips that hold a part without marking it.
    Thermal break
    Sleeving over hot-water and chilled lines, and at clamp points.
    Vibration and noise
    Mounts and spacers under panels, pumps and compressors.
    Dust and water sealing
    Compressible strips and gaskets on enclosures and panel edges.
    Weight reduction
    A foamed section in place of a solid one, at the same envelope.
    Handles and grips
    Soft-touch sleeves and covers on equipment that is handled daily.
Yutian · extruded silicone foam · cut to length

Silicone foam tubing, 15–70 Shore C and 0.2–1.0 g/cm³

Silicone compound extruded with a foaming agent, so the wall comes out light, compressible and thermally insulating while the bore stays smooth silicone. It is specified by density and hardness rather than by one section, which is why the same tube serves as cushioning, as a thermal break and as a soft sealing strip.

15–70 Shore C0.2–1.0 g/cm³−40 °C to +200 °C1–100 mmHB to V-0 (UL-94)

What a foamed silicone wall is

The compound is silicone mixed with a foaming agent and cured in the same extrusion step. The agent expands inside the wall, so the material that leaves the die is a fraction of the density of solid silicone and behaves like a spring: it compresses under load, recovers, and carries very little heat through itself.

The bore is still silicone, still smooth and still non-porous, so anything running inside the tube meets the same surface as on a solid silicone tube. What changes is everything outside that surface: weight, softness, the ability to absorb vibration, and thermal conductivity, which stays at or below 0.1 W/(m·K) across the range.

Because the wall is the part doing the work, a foam tube is quoted from two numbers — density and hardness — plus the section drawing. Those three decide weight, load-bearing and how much heat the wall stops.

Density and hardness are the two numbers to fix first

Every other property follows these two. Raising density and hardness raises tear strength, tensile strength and compression resistance, and lowers the insulation value; going the other way gives a lighter, softer, better insulating wall that carries less load and tears sooner at a sharp edge.

Typical bandDensity (g/cm³)Hardness (Shore C)What it is chosen for
Lightest0.2 – 0.3515 – 30Weight saving and insulation; the wall is softest and carries the least load.
General purpose0.4 – 0.630 – 50Cushioning, gap filling and sealing where the part is compressed in service.
Firmest0.7 – 1.050 – 70Load-bearing pads and strips that must hold shape under repeated compression.

Bands are working guidance, not a stock table: density is 0.2–1.0 ±0.1 g/cm³ and hardness 15–70 ±5 Shore C, and the pair is quoted for the part you order.

The published figures

These are the numbers the compound is held to, so they can be checked against a drawing before a sample is cut. Anything outside them — a lighter wall, a firmer pad, a 300 °C grade — is a different compound and is quoted separately rather than promised from this table.

PropertyValueUnitNote
Hardness15 – 70 ±5Shore CSet with the density
Density0.2 – 1.0 ±0.1g/cm³The main weight and insulation lever
Tear strength≥ 2kN/mRises with hardness
Tensile strength≥ 0.8MPaRises with hardness
Elongation at break≥ 200%Falls as hardness rises
Continuous temperature−40 to +200°C300 °C on request, custom compound
Compression set at 25%≤ 12%After the standard recovery cycle
Thermal conductivity≤ 0.1W/(m·K)Rises slightly with hardness
Flame classHB – V-0UL-94Grade quoted with the part
OdourSlight—As supplied
Restricted substancesRoHS—REACH declarations on request
Section size1 – 100mmWall and profile to the drawing

Section, wall and fit

Foam is made to a drawing: bore, outside diameter, wall and profile all come off the same die set, and the practical size limit is 1 mm to 100 mm, with sections up to 100 mm thick. Round tube, D-shape, rectangular strip and sheet are all the same process, so a strip with a flat face for bonding is no harder to quote than a tube.

The one thing to plan for is compression. A foam wall is meant to be squeezed, so the nominal size is only the free-state size: the working size is set by how much the part is compressed in its groove or clamp. That is why the drawing matters more here than on a solid tube, and why the fit is agreed with the groove width rather than guessed from the outside diameter.

Round tube

Cushioning and insulation over a core, or a soft sleeve over a cable or pipe.

Strip and profile

Flat-faced sections for bonding into a groove, a frame or a panel edge.

Sheet

Cut gaskets, pads and spacers from the same compound.

Temperature, compression and flame

Continuous service is −40 °C to +200 °C, which covers the hot side of most equipment and the cold side of chilled lines at the same time; a 300 °C grade exists as a custom compound and is quoted as such. Recovery is the property to look at on a clamped part: compression set at 25% is 12% or less, so a pad that is squeezed all day comes back to roughly its free thickness instead of taking a permanent set.

Flame class runs from HB to V-0 under UL-94, quoted with the part rather than assumed from the family, and the compound is documented to RoHS with REACH declarations on request. Low conductivity — 0.1 W/(m·K) or less — is what makes the same tube useful as a thermal break on a hot-water line and as a condensation barrier on a cold one.

Where foamed silicone earns its place

Cushioning and clamping

Pads, sleeves and strips that hold a part without marking it, and absorb the shock of a bump or a drop.

Thermal break

Sleeving over hot-water lines and cold lines, where a solid wall would conduct heat straight through the clamp.

Vibration and noise

Mounts and spacers under panels, pumps and compressors, where a soft wall damps the structure-borne part of the noise.

Sealing against dust and water

Compressible strips and gaskets on enclosures, doors and panel edges; the wall fills the gap instead of resisting it.

Weight reduction

Replacing a solid silicone section with a foamed one cuts mass at the same envelope, which matters on anything that moves.

Handles and grips

Soft-touch sleeves and covers where the outside has to be comfortable rather than chemical-resistant.

Where foam is the wrong part

A foamed wall is a low-modulus wall, and there are four places where that is the wrong answer. It is not a pressure part: anything that has to hold pressure or vacuum belongs to a reinforced tube. It is not an abrasion part: a foam outside wears through on a rubbing edge faster than a solid skin. It is not a precision bore: the wall moves under load, so a tight running fit cannot be held. And it is not a structural part: a clamped joint that has to carry load should not rely on the foam taking it.

Saying so before the order is cheaper than finding it on the line. If the line needs pressure or vacuum, the braided silicone hose range is the construction built for it, and the whole family sits under the foamed silicone tube range.

What you can specify

Density and hardness

Quoted as a pair: 0.2–1.0 ±0.1 g/cm³ with 15–70 ±5 Shore C. A lighter wall insulates better; a firmer wall holds its shape longer.

Colour

Any colour to a reference. Pigment is compounded into the wall, so it does not rub off the surface.

Profile and wall

Round, D-shape, strip or sheet, 1–100 mm, with the wall set on the drawing.

Adhesive backing

A pressure-sensitive backing can be applied to a flat face so the strip is positioned and pressed rather than bonded in place.

Bonded assemblies

Sections can be bonded into frames and loops; the bonded joint is part of the drawing rather than a field fix.

Length and packing

Cut to length or coiled, packed to the line item so a cell can pull the right part without measuring.

Three affiliated companies, one silicone chain

The tube is the last step of a chain controlled from the compound up. The three companies are affiliated: each is set up for one stage, and Yutian ships the part you buy.

Guilin Yutian New Materials

Silicone raw material and compound development, 28,000 m² site.

Dongguan Huahong Rubber and Plastic

Compounding, auxiliaries and batch control before extrusion.

Dongguan Yutian Silicone

Extrusion, foaming and finishing in a 6,800 m² plant.

Documents and the plant behind them

The compound is documented to RoHS, with REACH declarations issued on request. The plant runs an ISO 9001 and ISO 13485 quality system, and batches trace from compound to finished coil. If your market needs a declaration or a third-party report for the compound, say so in the enquiry: the two are different documents and are quoted as such.

Production runs on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, at a monthly capacity of up to 8 million metres, since 2012.

Lead time, samples and tooling

Stock sections

Ship in 5 to 7 working days.

Samples

Stock samples leave in 3 days; freight is paid by the buyer.

Custom section

10 to 20 working days after the drawing and the compound are agreed.

Tooling

A new profile or wall carries tooling at USD 100–400 per product, quoted once with the part.

Frequently asked questions

What is silicone foam tubing used for?

Cushioning, thermal insulation, vibration and noise damping, sealing against dust and water, and weight reduction: pads, sleeves, strips and gaskets that sit between two parts rather than carry fluid.

How do I specify the foam — by density or by hardness?

Send both, plus the section drawing. Density sets weight and insulation, hardness sets how firm the part feels under compression; the two move together, and a pair inside 0.2–1.0 g/cm³ and 15–70 Shore C covers most parts.

Is the bore the same as on a solid silicone tube?

Yes. Only the wall is foamed, so anything running inside meets a smooth, non-porous silicone surface, with the same cleaning behaviour as a solid tube.

What temperature does it take?

−40 °C to +200 °C continuous. A 300 °C grade is a custom compound and is quoted as a separate part rather than offered as a standard option.

Does the wall take a permanent set when clamped?

Compression set at 25% is 12% or less, so a pad returns to close to its free thickness. The working thickness still comes from how much the groove compresses the part, which is why the groove width belongs on the drawing.

Can it be bonded or supplied with adhesive backing?

Yes. A pressure-sensitive backing can be applied to a flat face, and sections can be bonded into frames or loops; both are quoted with the part.

Is it a pressure or vacuum part?

No. A foamed wall is a low-modulus wall and does not hold pressure or vacuum; reinforced constructions such as the braided hose range are the right part for those lines.

What are the order terms?

Stock sections ship in 5 to 7 working days, stock samples leave in 3 days, and a custom section takes 10 to 20 working days. Tooling for a new profile is USD 100–400 per product, quoted once.

Need a foamed section for a cushioning or insulation job?

Send the section drawing, the density or hardness you want, and the temperature it works in; you get the compound, the sample date and the tooling figure back in one reply.

Request a quote
WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com
Silicone foam tubing
Silicone foam tubing is extruded from silicone compound with a foaming agent, so the wall is light, compressible and thermally insulating. Supplied in −40 to +200 °C grades, 0.2–1.0 g/cm³ density and 15–70 Shore C hardness, cut to length or coiled. Colour, bore and wall are built to the drawing.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Silicone foam tubing

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.