Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Flame retardant silicone foam tube

Flame retardant foam silicone tubing is the foamed grade on a flame-retardant compound: a light, compressible wall that stops burning once the ignition source is removed. Compounds are rated UL-94 HB to V-0, with a UL yellow card or without, in −40 to +200 °C service, 0.2–1.0 g/cm³ and 15–70 Shore C.

    Product Features

    Flame-retardant silicone foam, rated UL-94 HB to V-0, with the worst-case grade quoted per part
    V-0 on a designated UL-recognised compound with its yellow card, or without the card at lower cost
    Self-extinguishing in the vertical test: stops burning once the ignition source is removed
    Foamed wall 0.2–1.0 ±0.1 g/cm³ and 15–70 ±5 Shore C, smooth non-porous silicone bore
    Continuous −40 °C to +200 °C; thermal conductivity ≤0.1 W/(m·K) and compression set ≤12% at 25%
    Sections 1–100 mm in round tube, D-shape, strip or sheet, cut to length or coiled

    Application

    Electrical enclosures
    Panel gaskets and edge seals that keep dust out without feeding a flame.
    Cable entries
    Soft sleeves and grommets where a local ignition source is a design case.
    Appliance and HVAC insulation
    Sleeving over hot parts inside a cabinet.
    Power supplies and transformers
    Pads and spacers where the enclosure specification asks for V-0.
    Lighting and display housings
    Seals and cushions behind drivers and connectors.
    EV and battery-pack padding
    Cushioning inside an enclosure specified to UL-94 V-0.

  • Parameters

    Product Features

    Flame-retardant silicone foam, rated UL-94 HB to V-0, with the worst-case grade quoted per part
    V-0 on a designated UL-recognised compound with its yellow card, or without the card at lower cost
    Self-extinguishing in the vertical test: stops burning once the ignition source is removed
    Foamed wall 0.2–1.0 ±0.1 g/cm³ and 15–70 ±5 Shore C, smooth non-porous silicone bore
    Continuous −40 °C to +200 °C; thermal conductivity ≤0.1 W/(m·K) and compression set ≤12% at 25%
    Sections 1–100 mm in round tube, D-shape, strip or sheet, cut to length or coiled

    Application

    Electrical enclosures
    Panel gaskets and edge seals that keep dust out without feeding a flame.
    Cable entries
    Soft sleeves and grommets where a local ignition source is a design case.
    Appliance and HVAC insulation
    Sleeving over hot parts inside a cabinet.
    Power supplies and transformers
    Pads and spacers where the enclosure specification asks for V-0.
    Lighting and display housings
    Seals and cushions behind drivers and connectors.
    EV and battery-pack padding
    Cushioning inside an enclosure specified to UL-94 V-0.
Yutian · flame retardant compound · UL-94 HB to V-0

Flame retardant foam silicone tube, rated HB to V-0

The same light, compressible foamed wall, on a compound that stops burning once the ignition source is taken away. V-0 is available two ways: on a designated UL-recognised compound with its yellow card, or on a non-card compound at a lower cost when your file does not call for UL.

UL-94 HB to V-0Yellow card on request−40 to +200 °C0.2–1.0 g/cm³1–100 mm

What the flame-retardant compound changes

A foamed wall is mostly structure: the foaming agent turns the silicone into a light wall with a lot of surface inside it, and internal surface is what a flame feeds on. The flame-retardant compound is what makes that wall stop burning when the ignition source goes away, instead of carrying a flame along the tube.

Nothing about the geometry changes. Density is still 0.2–1.0 g/cm³, hardness still 15–70 Shore C, the bore is still smooth silicone and the section is still 1–100 mm. The flame retardant sits in the compound, so it is there for the whole wall rather than as a coating that can be worn through.

That is the useful part for a buyer: the rating is a property of the material, quoted with the part, and it does not depend on how the tube is cut, bent or bonded.

What UL-94 HB, V-1 and V-0 actually test

UL-94 is a small-scale laboratory test, not a fire test of the finished machine. A specimen is held horizontally for HB, or vertically for V-0 to V-2, ignited for a fixed time and then watched: how long it keeps burning after the flame is removed, whether it drips, and whether the drip sets light to cotton placed below.

RatingHow it is testedWhat it means for the part
HBHorizontal specimen; the burn rate is measured along the barThe slowest-burning grade. It resists ignition but keeps burning horizontally at a limited rate.
V-2Vertical specimen; afterflame is timed and drips are caught on cottonSelf-extinguishing vertically, but burning drips are allowed to ignite the cotton.
V-1Vertical specimen; afterflame is timed, drips are caught on cottonSelf-extinguishing with no ignition of the cotton; drips are still permitted.
V-0Vertical specimen; afterflame ≤10 s each, ≤50 s total for five, no drip ignitionThe grade most specifications ask for: the wall stops burning quickly and does not drip fire.

Two things follow from that. First, the rating describes behaviour in a small specimen, so it tells you how the material reacts to a local ignition source — not how the assembled part behaves in a fire. Second, V-0 is the grade that most electrical and appliance specifications quote, which is why it is the one to fix first if your drawing names a rating at all.

With the yellow card, or without it

A UL yellow card is UL Component Recognition for the compound: the material is listed by UL under a file number, and that listing is what your own UL file cites when the finished product is submitted. Two supply options follow from that, and they are not the same thing.

V-0 with the yellow card

A designated UL-recognised compound, listed under a UL file number. Use this when the end product goes through UL and the material has to appear on a card; the card reference is quoted with the part. It carries the higher material cost of the two.

V-0 without the card

The same V-0 requirement met on a compound that is not UL-recognised — the cheaper option. It is right when the specification is internal or the market does not ask for a UL file, but it cannot be cited in a UL submission.

HB, either way

Where the drawing only asks for a slow-burning material rather than vertical self-extinguishing behaviour, HB is the grade that matches it.

Both are production options, and the choice is usually made by the end product rather than by the tube: if the machine is submitted to UL, the material has to be on a card and that means the designated compound. If it is not, the non-card V-0 grade does the same job in the part and costs less.

Where flame-retardant foam is used

Electrical enclosures

Panel gaskets and edge seals that have to keep dust out without adding a fuel path along the joint.

Cable entries and pass-throughs

Soft sleeves and grommets around cables entering a housing, where a local ignition source is a design case.

Appliance and HVAC insulation

Sleeving over hot parts inside a cabinet, where the foam must insulate and not carry a flame between components.

Power supplies and transformers

Pads and spacers around magnetics, where the enclosure specification asks for V-0.

Lighting and display housings

Seals and cushions behind a driver or a connector, quoted to the housing's rating.

EV and battery-pack padding

Cushioning inside an enclosure where the pack specification names UL-94 V-0.

The foam side is unchanged

A flame-retardant compound does not turn the tube into a different product family: it is still the foamed wall, still specified by density and hardness, still cut to the drawing. The table is the same as the standard foam tube, with the flame class moved to the top because on this part it is the reason the buyer is here.

PropertyValueUnitNote
Flame classHB – V-0UL-94Rating fixed with the compound
Hardness15 – 70 ±5Shore CSet with the density
Density0.2 – 1.0 ±0.1g/cm³Weight and insulation lever
Tear strength≥ 2kN/mRises with hardness
Tensile strength≥ 0.8MPaRises with hardness
Elongation at break≥ 200%Falls as hardness rises
Continuous temperature−40 to +200°C300 °C on request, different compound
Compression set at 25%≤ 12%Recovery after clamping
Thermal conductivity≤ 0.1W/(m·K)Rises slightly with hardness
Restricted substancesRoHS—REACH declarations on request
Section size1 – 100mmWall and profile to the drawing

Where foam is still the wrong part

A V-0 rating does not make a foamed wall structural, pressure-tight or fireproof. It is not a pressure or vacuum part: that belongs to a reinforced tube. It is not an abrasion part. It is not a precision bore, because the wall moves under load. And it is not a fire barrier: UL-94 describes how a small specimen reacts to a local flame, not how long an assembled part holds a fire back — that is a different test and a different specification.

Where the line needs pressure rather than padding, the braided silicone hose range is the construction for it; where the job is plain insulation at ambient temperature, the standard foam tubing page covers the same wall without the flame-retardant compound.

What you can specify

Rating and card

HB, V-1 or V-0, and whether the compound has to be UL-recognised. Naming the card and the rating at enquiry saves a material change later.

Density and hardness

0.2–1.0 ±0.1 g/cm³ with 15–70 ±5 Shore C, chosen as a pair.

Colour

Compounded into the wall to a reference. Flame-retardant compounds colour differently from the standard grades, so the colour is quoted with the rating.

Profile and wall

Round tube, D-shape, strip or sheet, 1–100 mm, wall set on the drawing.

Adhesive backing

A pressure-sensitive backing on a flat face, for strips that are positioned rather than bonded.

Bonded assemblies

Sections bonded into frames and loops, with the joint on the drawing.

Three affiliated companies, one silicone chain

The tube is the last step of a chain controlled from the compound up — which is where a flame rating is decided, because it lives in the compound rather than in the extrusion.

Guilin Yutian New Materials

Silicone raw material and compound development, 28,000 m² site.

Dongguan Huahong Rubber and Plastic

Compounding, auxiliaries and batch control before extrusion.

Dongguan Yutian Silicone

Extrusion, foaming and finishing in a 6,800 m² plant.

Documents and the plant behind them

The rating is stated per compound, and the UL yellow card for a recognised compound is quoted with the part. The compound is documented to RoHS, with REACH declarations on request, under an ISO 9001 and ISO 13485 quality system with batch traceability from compound to finished coil.

Production runs on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, at a monthly capacity of up to 8 million metres, since 2012.

Lead time, samples and tooling

Stock sections

Ship in 5 to 7 working days.

Samples

Stock samples leave in 3 days; freight is paid by the buyer.

Custom compound

10 to 20 working days after the rating and the drawing are agreed.

Tooling

A new profile or wall carries tooling at USD 100–400 per product, quoted once with the part.

Frequently asked questions

Is this tube UL-94 V-0?

The compounds are rated from HB up to V-0. V-0 is available on request; the rating for the part you order is fixed at quotation, because it belongs to the compound rather than to the section.

What is a UL yellow card, and do I need one?

It is UL Component Recognition for the compound, listed under a file number. It is supplied on a designated compound, so it is the version to choose when your own UL file has to cite a recognised material. If the end product is not submitted to UL, the card is not needed.

Can you supply V-0 without the yellow card?

Yes, and it is the cheaper of the two. The part is a flame-retardant V-0 material, but the compound is not UL-recognised, so it cannot be cited in a UL submission. Say which of the two you need before the sample is cut.

Which version costs more?

The yellow-card version, because it runs on a designated UL-recognised compound. The non-card V-0 grade meets the same UL-94 V-0 requirement at a lower material cost; both are quoted on the same drawing, so the difference is visible in the quotation.

Does the flame retardant change the temperature range?

No. Continuous service is −40 °C to +200 °C, as on the standard foam tube; a 300 °C grade is a different compound and is quoted separately.

Does it make the foam harder?

Density and hardness stay in the same bands — 0.2–1.0 g/cm³ and 15–70 Shore C — and are chosen as a pair. The flame-retardant compound is what changes, not the geometry.

What sizes and sections are available?

Round tube, D-shape, strip and sheet from 1 mm to 100 mm, wall set on the drawing, cut to length or coiled.

Can it be bonded or supplied with adhesive backing?

Yes. A pressure-sensitive backing can be applied to a flat face, and sections can be bonded into frames or loops; both are quoted with the part.

What are the order terms?

Stock sections ship in 5 to 7 working days, stock samples leave in 3 days, and a custom compound or section takes 10 to 20 working days. Tooling for a new profile is USD 100–400 per product, quoted once.

Need a V-0 section for an enclosure or a cabinet?

Send the rating your file calls for, whether the material has to be UL-recognised, and the section drawing; you get the compound, the sample date and the tooling figure back in one reply.

Request a quote
WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com
Flame retardant silicone foam tube
Flame retardant foam silicone tubing is the foamed grade on a flame-retardant compound: a light, compressible wall that stops burning once the ignition source is removed. Compounds are rated UL-94 HB to V-0, with a UL yellow card or without, in −40 to +200 °C service, 0.2–1.0 g/cm³ and 15–70 Shore C.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Flame retardant silicone foam tube

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.