Demand Submission
Please leave us a message and we will contact you within 24 hours
PRODUCTS
Specializing in the production of highquality silicone rubber products
PRODUCT
Specializing in the production of highquality silicone rubber products
— Product Categories
Silicone tube
LED light strip silicone sleeve
Foamed silicone tube
Silicone braided tube
Medical silicone tube
Peristaltic pump silicone hose
Communication/power shrink tubing
Silicone shielding strip
Foam silicone sealing strip
Silicone sealing strip/ring
Bicycle handle cover/strap
Silicone sheets and miscellaneous parts
Silicone leather
— News Recommended
top Introducing the Innovative Foam Silicone Tube:...
top Enhancing the Lifespan of High-Temperature Sil...
top Colored Silicone Tube: Production Process and ...
Custom Silicone Foam Tube: Sizes, Colors, and ...
UL94 V-0 Silicone Foam Tube for EV Battery Pro...
Food Grade Silicone Foam Insulation Tube: FDA ...
Silicone Foam Tube vs EPDM Rubber Foam: Which ...
Platinum-Cured vs Peroxide-Cured Silicone Foam...
— Products Recommended

Flat top-emitting (direct-lit) silicone diffuser, platinum-cured and compounded in our Dongguan plant. Panels 1.0–5.0 mm thick, up to 1200 mm wide and 100 m long; IP67/IP68 optional. Transmittance is engineered per project against your profile and strip. Minimum order value USD 500; free samples of standard stock items.
A platinum-cured silicone panel that sits directly above the LED board and sends light out through a flat face. We compound the silicone in our own plant, so transmittance is set for your strip and your target light effect — not copied from a catalogue.

A flat top-emitting diffuser is a planar silicone panel placed directly in front of the LEDs. The board sits behind the panel, light enters the back face and leaves through the flat front surface, so the whole face reads as one even glow instead of a row of dots. It is not a sleeve that wraps a strip, and not a side-lit profile that throws light from an edge.
Three formats are often confused when buyers ask for a “diffuser”. The table below separates them, and the two other formats link to their own pages: a side-lit flat diffuser and a sleeve for LED strip.
| Format | How the strip sits | Typical use |
|---|---|---|
| Flat top-emitting panel (this page) | Board directly behind a flat panel; light leaves through the face | Light boxes, panels and coves that need one even glowing surface |
| Side-lit flat diffuser | LEDs along an edge; light travels sideways through the panel | Thin profiles and frames with an edge channel |
| Sleeve for LED strip | Strip is threaded inside an extruded sleeve | Linear runs, IP-rated strips and flexible contours |
Three affiliated companies cover the chain from silicone raw material to the finished part. Each keeps its own scope; together they let us change a compound and re-test a panel inside the same group.
Silicone raw materials and compounds for our extrusion and moulding lines.
Compounding and auxiliary materials, including the fillers that set diffusion and colour.
Extrusion, calendering, moulding and finishing in our 6,800 m² plant in Changping, Dongguan.
We are a silicone factory, not a lighting brand. Buyers come to us for the part that sits between the LED board and the eye — and for a supplier who can change the compound when the light effect is not right.
Transmittance and colour are adjusted through formulation before the panel is extruded. That is the step we keep in-house from raw material to finished part.
We do not publish one transmittance figure for every strip. We ask for the profile, the strip data and the target effect, then measure a sample of your geometry.
Extrusion, calendering, moulding, bonding and assembly in one plant: 14 extrusion lines, 4 calendering lines, 7 compression moulding lines, 90+ production staff and 50+ management and sales staff.
Class 100,000 cleanroom for production. ROHS, REACH and UL94 documentation is held at raw-material level; product-specific test reports are arranged as a separate project.
Six decisions decide whether a diffuser reads as a clean sheet of light or as a row of bright dots. Ours are made with the strip in hand, not from a catalogue page.
Milky white and translucent compounds forward light in different ways. Filler loading, hardness and wall thickness all shift the result, so we move transmittance through the compound and then confirm it on a sample of your profile.
Strip efficacy and LED count or pitch; the distance between the board and the emitting surface; and the transmittance of the compound. Change one and the others move with it, which is why we ask for all three before quoting a panel.
Platinum-cured silicone is odourless and low in volatiles. It stays flexible across the −40 °C to +200 °C range and is the standard cure across almost all of our silicone products.
The emitting surface is formed flat, so the panel can sit against a frame, a light box backplate or a ceiling recess without a visible gap or a second optical film.
Where a fixture needs it, panels can be supplied as an assembly rated IP67 or IP68. The grade depends on the profile, the sealing method and the end caps, so it is confirmed per project.
1.0–5.0 mm thickness as standard, 0.5–10.0 mm on request; width up to 1200 mm; length up to 100 m. Panels ship flat or coiled for a continuous line.
Published catalogue ranges for the diffuser panel. Where a project needs a guaranteed value, the approved sample and its approval sheet govern.
| Property | Standard range | On request |
|---|---|---|
| Material | Platinum-cured optical-grade silicone | Custom compound |
| Form | Flat top-emitting panel or sheet | Coiled or flat |
| Thickness | 1.0–5.0 mm | 0.5–10.0 mm |
| Width | Up to 1200 mm | Narrower slit widths |
| Length | Up to 100 m | Cut to length |
| Hardness | 40–70 Shore A | 30–80 Shore A |
| Colour | Opal (milky white), translucent | Colour matching |
| Optical performance | Engineered per project | Measured on your sample |
| Operating temperature | −40 °C to +200 °C | — |
| Ingress protection | IP67 / IP68 (assembly, optional) | — |
| Flammability | UL94 HB (raw-material level) | — |
| Documentation | ROHS and REACH at raw-material level | Product-specific test project |
Length is supplied up to 100 m. Thickness, width, hardness and colour are confirmed on the approval sheet before production.
Six fixture families cover most of the requests we quote. If your design is outside them, send the drawing anyway — the question is whether the panel can be extruded flat at your thickness.
Linear panels and light coves where the face has to read as one continuous glow.
Retail, exhibition and menu backlights with a shallow cavity behind the face.
Ceiling and wall luminaires that call for a soft, low-glare emitting surface.
Bollards, wall washers and façade lines where an IP-rated assembly is needed.
Large letter faces that need a flat, even surface instead of a hot spot at the LED.
Inspection and task lights that must stay bright in heat, dust and cleaning cycles.

Six inputs are enough for a quotation and a sample proposal. Without the strip data we can still quote the panel, but not the light effect.
Minimum order value is USD 500. Unit price is quoted per project, because compound, thickness and tolerance change with the strip.
Samples of standard stock items are sent free of charge, usually dispatched within 3 days.
A sample in your compound, thickness and colour is quoted with the project; timing is confirmed when the specification is agreed.
Standard items 5–7 days. Custom items 10–20 working days after sample approval.
Certificates below cover our compounds and our management system. They do not mean that every finished panel has been individually tested — a product-specific test report is a separate project, and we say so before an order.
| Standard | What it covers | Level |
|---|---|---|
| ISO 9001:2015 | Quality management system | Company level |
| ROHS | Restricted substances | Raw-material level |
| REACH | Substance registration | Raw-material level |
| UL94 HB | Flammability of the compound | Raw-material level |
| Class 100,000 cleanroom | Production environment | In use |
Monthly inspection pass rate is 95% or higher and batch acceptance pass rate is 99%. Our plant is 6,800 m² in Changping, Dongguan.
They describe two sides of the same setup. Top-emitting names the flat face the light leaves from; direct-lit names where the board sits — directly behind the panel, not along an edge. Side-lit and edge-lit designs put the LEDs at the edge and are a different product.
Three inputs decide it: strip efficacy and LED pitch, the distance from the board to the emitting surface, and the transmittance of the compound. We adjust the compound and confirm the result on a sample of your geometry. No single thickness or distance fixes every strip, so we do not quote one.
Yes, within the limits of the compound. Send the profile drawing, the strip specification and the target effect; we make a sample and measure it. The approved sample and its approval sheet become the production reference.
Silicone is chosen for LED diffusers because it holds up under heat and UV without the hazing that affects many polymers. We formulate for long outdoor and high-temperature use, and confirm the grade against your application rather than a fixed hour count.
−40 °C to +200 °C. A fixture that runs above that range is outside our standard compounds; tell us the conditions and we will say whether we can compound for them.
The panel itself is a solid silicone part. Where the fixture needs an IP rating, it is supplied as an assembly rated IP67 or IP68, depending on the profile, the sealing method and the end caps.
1.0–5.0 mm thickness as standard, 0.5–10.0 mm on request; up to 1200 mm wide and up to 100 m long; hardness 40–70 Shore A, 30–80 on request.
USD 500 in order value. Samples of standard stock items are free; custom samples are quoted with the project.
The other silicone LED parts we make, and the two guides that explain how the formats differ:
Browse the full LED silicone parts category for sleeves, profiles, neon flex and accessories.
A profile drawing, the strip data and the target light effect are enough for us to quote and to propose a sample. Tell us the fixture; we will tell you what the compound can do.
salesmanager@yutiansilicone.com · Mobile / WhatsApp +86 180 2892 1514
DongGuan Yutian Silicone Rubber Technology Co., Ltd
Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China
Silicone manufacturer since 2012

Copy product links
Long by picture save/share


— News Recommended
top Introducing the Innovative Foam Silicone Tube: A High-Perfor...
top Enhancing the Lifespan of High-Temperature Silicone Tubes in...
top Colored Silicone Tube: Production Process and How to Choose
Custom Silicone Foam Tube: Sizes, Colors, and Specifications...
UL94 V-0 Silicone Foam Tube for EV Battery Protection: Safet...
Food Grade Silicone Foam Insulation Tube: FDA Compliance and...
— Products Recommended
Message
Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.