Demand Submission
Please leave us a message and we will contact you within 24 hours
PRODUCTS
Specializing in the production of highquality silicone rubber products
PRODUCT
Specializing in the production of highquality silicone rubber products
— Product Categories
Silicone tube
LED light strip silicone sleeve
Foamed silicone tube
Silicone braided tube
Medical silicone tube
Peristaltic pump silicone hose
Communication/power shrink tubing
Silicone shielding strip
Foam silicone sealing strip
Silicone sealing strip/ring
Bicycle handle cover/strap
Silicone sheets and miscellaneous parts
Silicone leather
— News Recommended
top Introducing the Innovative Foam Silicone Tube:...
top Enhancing the Lifespan of High-Temperature Sil...
top Colored Silicone Tube: Production Process and ...
Custom Silicone Foam Tube: Sizes, Colors, and ...
UL94 V-0 Silicone Foam Tube for EV Battery Pro...
Food Grade Silicone Foam Insulation Tube: FDA ...
Silicone Foam Tube vs EPDM Rubber Foam: Which ...
Platinum-Cured vs Peroxide-Cured Silicone Foam...
— Products Recommended

Moulded silicone end caps and mounting clips for the silicone LED profiles we extrude. Closed caps or caps with a cable hole, aluminium clips for the neon sections and silicone clips for the square, D and U waterproof sleeves. −40 °C to +200 °C; IP67/IP68 as a sealed assembly.
End caps and mounting clips for the silicone profiles we extrude. Closed caps and caps with a cable hole, matched to the section — with the split between families stated plainly.

These are the parts that finish a silicone profile: moulded end caps that close the run, and clips that hold it where there is no surface to bond to. Both are made for the profiles we extrude, so the fit is set by the section, not guessed from a photograph.
Not every format takes them. The neon-family sections and the square, D and U waterproof sleeves are made for caps and clips; the flush covers, the braided round tubes and the 270°/180° versions are supplied as plain profiles. The table below is the honest version of that split. If you are choosing the profile as well, start from the silicone sleeve for LED strip or the wide-angle neon flex, then come back here for the ends.
Caps are moulded in silicone, in a closed version and a version with a cable hole. Where the run has to be watertight, the cap plus the sealing method is what carries the IP67 or IP68 rating of the assembly, so the method is agreed before the order.
Extrusion is the last step of a chain we control from the compound up. The three companies below are affiliated; each does what it is set up for, and Yutian handles the profile you buy.
silicone raw materials and auxiliary materials
compound development and mixing
extrusion, finishing and packing in our 6,800 m² plant in Changping, Dongguan
Transmittance, colour and flexibility come from the compound. Because we compound and extrude, a change in the light effect is a formulation change, not a new supplier.
We work from the section drawing or the groove you have to fill, and tell you whether an existing die fits or a new one is needed.
Cut to length and packed to suit your line. Where the fixture needs a sealed end, the method is agreed before the order.
Certificates are described at the level they are held. Where a product-specific test report is needed, it is quoted as a separate project instead of implied.
Caps and clips are made against the same section drawing as the profile, so the cap sits square on the end and the clip grips the wall it was designed for.
One cap closes a dead end; the other lets the supply in. Both exist as standard parts for the families in the table.
The rating is stated for the assembly, together with the method that achieves it, instead of being printed on a bag of caps.
Silicone caps take the same temperature range as the profile and stay soft, so a sealed end does not crack where the cable enters.
Aluminium clips for the neon sections, silicone clips for the waterproof sleeves — the table tells you which before you order.
A section outside the catalogue is a mould project with a real lead time and a real price, quoted from your drawing.
You do not have to buy the profile again to get the ends. Order caps and clips against the section you already run.
Caps and clips can ship together with the extrusion, counted per run, so nothing is short on the fitting line.
Which family takes which accessory, according to the current catalogue. Anything outside this table is a development project, not a stock pair.
| Profile family | End cap | Clip | Note |
|---|---|---|---|
| Multi-colour neon sections | Straight-out cap | Aluminium clip | Cap and clip both available |
| Square, D and U waterproof sleeves | Silicone cap | Silicone clip | IP67 / IP68 with the sealing method |
| Flush covers | Not supplied | Not supplied | Plain profile only |
| Braided round tubes | Not supplied | Not supplied | Plain profile only |
| 270° / 180° arc profiles | Not supplied | Not supplied | Plain profile only |
Caps are moulded silicone. A custom shape is a mould project with its own lead time; we quote it with the drawing rather than promise it as a stock item.
| Type | What it does | Where it is used |
|---|---|---|
| Closed cap | Seals the end of the run | Termination with no cable exit |
| Cap with cable hole | Pre-formed hole for the supply | Power input end |
| Custom cap | Made to your drawing | Non-standard sections and hole layouts |
These values cover the accessory parts. The rating of a finished fixture depends on the cap, the sealant and the way the cap is bonded.
| Property | Value |
|---|---|
| Cap material | Moulded silicone |
| Clip materials | Aluminium, or silicone for the waterproof sleeves |
| Service temperature | −40 °C to +200 °C |
| Sealing | IP67 or IP68 as a sealed assembly, method agreed per project |
| Colour | Natural white; other colours quoted |
| Fit | Matched to the section or to your drawing |
| Minimum order value | USD 500 |
Sample approval confirms the fit on the profile you are using.
Closed ends on letters and light boxes.
Sealed terminations where the fixture sees weather.
End caps and clips for the multi-colour sections.
Small clips where the surface cannot be bonded.
Caps that finish a shelf edge cleanly.
Caps and clips packed with the profile per run.
Send the section you are using, or the drawing of the cap you need. For a stock family we match the existing cap; for anything else we quote the mould with the parts.
Fit and sealing are confirmed on the sample approval sheet.
Samples of standard stock items are sent free of charge, usually dispatched within 3 days.
A run in your compound, section or cut length is quoted with the project, including any die.
Standard items 5–7 days. Custom items 10–20 working days after sample approval.
The certificates below cover our compounds and our management system. They do not mean that every finished profile has been individually tested; a product-specific test report is a separate project and is quoted as one.
| Standard | What it covers | Level |
|---|---|---|
| ISO 9001:2015 | Quality management system | Company level |
| ROHS | Restricted substances | Raw-material level |
| REACH | Substance registration | Raw-material level |
| UL94 HB | Flammability of the compound | Raw-material level |
| Class 100,000 cleanroom | Production environment | In use |
Monthly inspection pass rate is 95% or higher and batch acceptance pass rate is 99%.
Only where the catalogue lists them for that section. Flush covers, braided tubes and arc profiles are supplied as plain profiles; the neon sections and the square, D and U sleeves are the families that take caps and clips.
A cap is one part of the seal. The IP67 or IP68 rating belongs to the finished assembly, and it depends on the sealing method and how the cap is bonded, so the method is agreed before the order.
Yes, as a mould project. Send the section drawing and we quote the tool with the parts. It is quoted separately from the extrusion.
Both versions exist: closed, and with a pre-formed hole for the supply. Where the cable size is unusual, the hole is made to your drawing.
Aluminium for the neon-family sections; silicone for the square, D and U waterproof sleeves. The table above shows which family takes which.
Yes. They are supplied as parts in their own right, matched to the profile you already use. Tell us the section and the quantity.
−40 °C to +200 °C, the same range as the profiles they fit.
Minimum order value USD 500. Stock samples are free; custom caps are quoted with the tool. Standard parts ship in 5–7 days, custom moulds in 10–20 working days after sample approval.
The other silicone LED parts we make, and the guides that explain how the formats differ:
Browse the full LED silicone parts category for sleeves, profiles, neon flex and accessories.
Tell us the section and the quantity. We will confirm the fit, quote the parts or the mould, and send samples to check before the order.
salesmanager@yutiansilicone.com · Mobile / WhatsApp +86 180 2892 1514
DongGuan Yutian Silicone Rubber Technology Co., Ltd
Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China
Silicone manufacturer since 2012

Copy product links
Long by picture save/share


— News Recommended
top Introducing the Innovative Foam Silicone Tube: A High-Perfor...
top Enhancing the Lifespan of High-Temperature Silicone Tubes in...
top Colored Silicone Tube: Production Process and How to Choose
Custom Silicone Foam Tube: Sizes, Colors, and Specifications...
UL94 V-0 Silicone Foam Tube for EV Battery Protection: Safet...
Food Grade Silicone Foam Insulation Tube: FDA Compliance and...
— Products Recommended
Message
Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.