Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Silicone Snap-on Cover for LED Aluminum Profiles

Silicone snap-on cover for LED aluminum profiles, eight sections from 14 x 10 mm to 57 x 20 mm with slots from 10 x 10 mm to 50 x 20 mm. Presses into the profile by hand; platinum-cured silicone, 70 +/- 5 Shore A, -40 to +200 C. Supplied without end caps or clips.

    Product Features

    Silicone snap-on cover that presses into the slot of an aluminum profile, no tools
    8 standard sections from 14 × 10 mm to 57 × 20 mm
    Slots from 10 × 10 mm to 50 × 20 mm, matched to the profile drawing
    Platinum-cured silicone, 70 ± 5 Shore A, −40 °C to +200 °C
    Supplied as the cover only: no end caps, no clips
    Cut lengths to your schedule; USD 500 minimum order value

    Application

    Linear fixtures
    Aluminum profiles for offices, retail and display lighting.
    Architectural lines
    Reveal and cove details where the profile is set into the build.
    Cabinet and shelf
    Shelf edges and wardrobe lines with a clean, flush face.
    Signage
    Light lines in letters, boxes and panel edges.
    Outdoor and facade
    Profiles that see weather and temperature swings.
    OEM luminaires
    Covers cut and packed for a fixture maker's line.

  • Parameters

    Product Features

    Silicone snap-on cover that presses into the slot of an aluminum profile, no tools
    8 standard sections from 14 × 10 mm to 57 × 20 mm
    Slots from 10 × 10 mm to 50 × 20 mm, matched to the profile drawing
    Platinum-cured silicone, 70 ± 5 Shore A, −40 °C to +200 °C
    Supplied as the cover only: no end caps, no clips
    Cut lengths to your schedule; USD 500 minimum order value

    Application

    Linear fixtures
    Aluminum profiles for offices, retail and display lighting.
    Architectural lines
    Reveal and cove details where the profile is set into the build.
    Cabinet and shelf
    Shelf edges and wardrobe lines with a clean, flush face.
    Signage
    Light lines in letters, boxes and panel edges.
    Outdoor and facade
    Profiles that see weather and temperature swings.
    OEM luminaires
    Covers cut and packed for a fixture maker's line.

A cover that presses into the profile, no tools and no screws

Extruded silicone cover shaped to latch into the slot of an aluminum profile. The cover presses in by hand, takes up the tolerance of the extrusion, and leaves a clean, even line of light along the run.

8 sections, 14 × 10 to 57 × 20 mmSlots from 10 × 10 to 50 × 20 mm−40 °C to +200 °CIP67 / IP68 when sealed
Silicone snap-on cover for LED aluminum profiles
The cover presses into the profile slot by hand, with no tools and no screws.

What a snap-on cover for an aluminum profile is

An aluminum profile holds the strip; the cover is the part you see. A snap-on cover has two lips on the underside that flex as it is pressed into the channel and then hold it there, so the cover can be fitted after the strip is wired and tested.

Two dimensions decide whether it fits: the slot width of the profile and the slot depth behind the lips. Our eight standard sections are described by both, so a profile can be matched to a cover without a drawing.

The cover is supplied without end caps and without clips, because on this format the profile itself does the holding. Where the run has to be closed at the ends, that is handled in the fixture design or agreed separately.

Three affiliated companies, one silicone chain

Extrusion is the last step of a chain we control from the compound up. The three companies below are affiliated; each does what it is set up for, and Yutian handles the profile you buy.

Guilin Yutian New Materials

silicone raw materials and auxiliary materials

Dongguan Huahong Rubber & Plastic Material Co., Ltd

compound development and mixing

Dongguan Yutian Silicone Rubber Technology Co., Ltd

extrusion, finishing and packing in our 6,800 m² plant in Changping, Dongguan

Why buyers place the profile with us

Compound in our own hands

Transmittance, colour and flexibility come from the compound. Because we compound and extrude, a change in the light effect is a formulation change, not a new supplier.

Extrusion from your drawing

We work from the section drawing or the groove you have to fill, and tell you whether an existing die fits or a new one is needed.

Finishing and accessories

Cut to length and packed to suit your line. Where the fixture needs a sealed end, the method is agreed before the order.

Paperwork that matches the claim

Certificates are described at the level they are held. Where a product-specific test report is needed, it is quoted as a separate project instead of implied.

Key advantages

Fitted after wiring

The strip goes into the profile, the run is tested, and the cover presses on last. Rework on site does not mean scrapping a bonded cover.

No screws, no clips

Two moulded lips hold the cover in the slot. There are no separate fasteners to lose and no tools needed along the run.

Tolerance taken up by the silicone

An aluminum extrusion is never perfectly straight. A flexible cover presses in over the variation instead of standing proud where the profile bows.

Slot matched, not guessed

Each section is defined by slot width and slot depth. Send the profile drawing and the fit is checked against the eight sections before a sample is cut.

A line, not a row of dots

The wall blends the strip into a continuous line. How even it reads is settled on the sample, with your strip and your profile in the same test.

Stays supple in the cold

Silicone does not turn brittle at low temperature the way rigid plastic lenses can, so a cover fitted outdoors keeps its seat through winter.

Cut on site with a knife

The cover trims with a sharp blade and the cut end sits in the profile, so the last metre of a run does not need a workshop.

Tint matched to a sample

Clear, opal or tinted compounds are made in-house, so the colour of the line can be matched to a physical sample rather than to a screen.

Standard sections

The size column is the cover's outside dimension. The two slot columns are what has to match the aluminum profile: the opening the cover presses into, and the depth behind the lips.

SectionCover sizeModelSlot widthSlot depth
101014 × 10 mmHJS-1865910 mm10 mm
121016 × 10 mmHJS-1866112 mm10 mm
161620 × 15 mmHJS-1866016 mm16 mm
201024 × 10 mmHJS-1866220 mm10 mm
241424 × 14 mmHJS-1865820 mm14 mm
302037 × 20 mmHJS-1866330 mm20 mm
402047 × 20 mmHJS-1866440 mm20 mm
502057 × 20 mmHJS-1866550 mm20 mm

Model numbers are internal references, quoted so a repeat order returns to the same die. A profile outside this list is quoted as a new section from its drawing.

Silicone cover and rigid plastic lens

Silicone snap-on coverRigid plastic lens
FittingPresses in by hand, lips hold itUsually clipped, screwed or capped
Profile toleranceFlexes over a bowed extrusionRigid, so gaps show at the ends
ColdStays suppleCan become brittle
Cutting on siteSharp knifeSaw or guillotine
ColourCompound tinted in-housePigment in a plastic masterbatch

Neither format is better everywhere. The silicone cover wins where the profile is long, the site work is awkward, or the fixture moves between indoor and outdoor use.

Technical specification

ParameterValue
MaterialPlatinum-cured silicone, clear or translucent compound
Hardness70 ± 5 Shore A
Density1.2 ± 0.1 g/cm³
Tensile strength≥ 8 MPa
Elongation at break≥ 300 %
Tear strength≥ 30 kN/m
Service temperature−40 °C to +200 °C
FlammabilityUL94 HB, raw-material level
ColourClear, translucent, opal or tinted to a physical sample
Cover size14 × 10 mm to 57 × 20 mm in the standard sections
Slot width10 mm to 50 mm
Slot depth10 mm to 20 mm
IP ratingIP67 or IP68 when the fixture is sealed as an assembly
Supplied withCover only; no end caps, no clips
LengthCut lengths to your schedule
Minimum orderUSD 500 order value

Values above describe the compound and the section, not a measured optical result. Evenness is confirmed on a sample built with your strip and profile.

Applications

The cover is chosen with the profile, because the slot is the interface:

Linear fixtures

Aluminum profiles for offices, retail and display lighting.

Architectural lines

Reveal and cove details where the profile is set into the build.

Cabinet and shelf

Shelf edges and wardrobe lines with a clean, flush face.

Signage

Light lines in letters, boxes and panel edges.

Outdoor and facade

Profiles that see weather and temperature swings.

OEM luminaires

Covers cut and packed for a fixture maker's line.

Made to your profile

The slot is the only thing that has to be right: send the profile drawing or a short sample, and the cover is matched to it.

  • Profile drawing, or the slot width and slot depth
  • Strip width and height that sit in the profile
  • Cover size and wall thickness
  • Colour and tint, matched to a physical sample
  • Cut length and packing
  • Whether the run needs to be sealed at the ends

A profile outside the eight standard sections is quoted as a new die before production.

Samples and lead time

Stock samples: free

Samples of standard stock items are sent free of charge, usually dispatched within 3 days.

Custom runs: quoted

A run in your compound, section or cut length is quoted with the project, including any die.

Production lead time

Standard items 5–7 days. Custom items 10–20 working days after sample approval.

Certificates and quality

The certificates below cover our compounds and our management system. They do not mean that every finished profile has been individually tested; a product-specific test report is a separate project and is quoted as one.

StandardWhat it coversLevel
ISO 9001:2015Quality management systemCompany level
ROHSRestricted substancesRaw-material level
REACHSubstance registrationRaw-material level
UL94 HBFlammability of the compoundRaw-material level
Class 100,000 cleanroomProduction environmentIn use

Monthly inspection pass rate is 95% or higher and batch acceptance pass rate is 99%.

Frequently asked questions

What is a snap-on cover for an aluminum profile?

An extruded silicone cover with lips on the underside that flex into the profile channel and hold the cover in place. It is fitted after the strip is wired and tested.

How do I know which section fits my profile?

By the slot: the opening the cover presses into and the depth behind the lips. Send the profile drawing or a short sample and the fit is checked against the eight sections.

Do you supply end caps and clips?

No. On this format the profile holds the cover, so it is supplied as the cover alone. Where a run has to be closed at the ends, that is agreed with the fixture design.

Will it yellow in outdoor use?

The compound is a UV-stable silicone rather than a plasticised plastic. Any claim about appearance over time is confirmed on the sample you approve, and we do not quote a catalogue number of years.

Does it hide the dots of the strip?

The wall blends the strip, but how even the line looks depends on the strip, the depth from strip to cover and the wall thickness. We test it with your strip and profile and approve the sample.

Can it be cut on site?

Yes, with a sharp knife. The cut end sits inside the profile, so a run can be finished without workshop tooling.

Is the cover waterproof?

The cover is solid silicone. The rating belongs to the sealed fixture: with the ends and the profile sealed as an assembly, the result is IP67 or IP68.

What are the order terms?

Minimum order value USD 500. Stock samples are free; custom runs are quoted. Standard items ship in 5–7 days, custom items in 10–20 working days after sample approval.

Related silicone LED parts

The other silicone LED parts we extrude, and the guides that explain how the formats differ:

Browse the full LED silicone parts category for sleeves, diffusers, neon flex and covers.

Need a cover that fits the profile you already use?

Send the profile drawing or the slot width and depth. We will confirm the section, or quote a die from your drawing.

salesmanager@yutiansilicone.com · Mobile / WhatsApp +86 180 2892 1514
DongGuan Yutian Silicone Rubber Technology Co., Ltd
Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China
Silicone manufacturer since 2012

Silicone Snap-on Cover for LED Aluminum Profiles
Silicone snap-on cover for LED aluminum profiles, eight sections from 14 x 10 mm to 57 x 20 mm with slots from 10 x 10 mm to 50 x 20 mm. Presses into the profile by hand; platinum-cured silicone, 70 +/- 5 Shore A, -40 to +200 C. Supplied without end caps or clips.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Silicone Snap-on Cover for LED Aluminum Profiles

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.