Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Silicone Neon Flex Diffuser, 270° D-Shape & 360° Round

Silicone neon flex diffuser, extruded in two emission angles: a 270° D-shape with a flat back for wall and sign outlines, and a 360° round tube that reads the same from every side. D-shape Ø13/Ø20/Ø22 mm, round Ø13/Ø18/Ø20/Ø30 mm, 5–10 mm strip cavities, −40 to +200 °C, IP67/IP68 as a sealed assembly.

    Product Features

    Silicone neon flex diffuser in two emitting geometries: 270° D-shape and 360° round
    D-shape sections Ø13, Ø20 and Ø22 mm; round sections Ø13, Ø18, Ø20 and Ø30 mm
    PCB cavities of 5 mm, 8 mm and 10 mm for the strips most neon flex fixtures use
    Platinum-cured translucent silicone, 70 ± 5 Shore A, −40 °C to +200 °C
    Light performance engineered per project: evenness confirmed on a sample of your strip
    Sealed assembly to IP67 or IP68; continuous coils or cut lengths; USD 500 minimum order value

    Application

    Architectural outlines
    Facade lines, wall grazing and cove details.
    Signage and channel letters
    Even illumination across letters and logo outlines.
    Retail and hospitality
    Feature lines, shelving accents and bar fronts.
    Suspended and freestanding runs
    Round tube for lines seen from every side.
    Landscape and facade accents
    Outdoor lines where UV and heat both apply.
    Exhibition and furniture
    Curved detail lighting in joinery and stands.

  • Parameters

    Product Features

    Silicone neon flex diffuser in two emitting geometries: 270° D-shape and 360° round
    D-shape sections Ø13, Ø20 and Ø22 mm; round sections Ø13, Ø18, Ø20 and Ø30 mm
    PCB cavities of 5 mm, 8 mm and 10 mm for the strips most neon flex fixtures use
    Platinum-cured translucent silicone, 70 ± 5 Shore A, −40 °C to +200 °C
    Light performance engineered per project: evenness confirmed on a sample of your strip
    Sealed assembly to IP67 or IP68; continuous coils or cut lengths; USD 500 minimum order value

    Application

    Architectural outlines
    Facade lines, wall grazing and cove details.
    Signage and channel letters
    Even illumination across letters and logo outlines.
    Retail and hospitality
    Feature lines, shelving accents and bar fronts.
    Suspended and freestanding runs
    Round tube for lines seen from every side.
    Landscape and facade accents
    Outdoor lines where UV and heat both apply.
    Exhibition and furniture
    Curved detail lighting in joinery and stands.

Two emission angles, one silicone neon flex diffuser

A silicone neon flex diffuser, extruded in two emitting geometries for 5–10 mm LED strips. The D-shape concentrates the arc over one face; the round tube emits all round. Both follow a curve and stay even along the run.

270° D-shape: Ø13 / Ø20 / Ø22 mm360° round: Ø13 / Ø18 / Ø20 / Ø30 mm−40 °C to +200 °CIP67 / IP68 when sealed
Milky white silicone neon flex tubes with an internal strip channel, 270 degree D-shape and 360 degree round

What a silicone neon flex diffuser is

Neon flex is the finished light: a flexible LED strip inside an extruded silicone diffuser. We make the diffuser itself — the extruded silicone wall that carries the strip, spreads the dots and sets the emitting arc. The angle describes the emitting arc, not a lens: a 270° D-shape has a flat back to sit against a surface and emits over a wide arc from the front, while a 360° round tube emits all round and reads the same from every viewing angle.

Use the D-shape for outlines on a plane — a wall, a sign, a facade line — where the back is fixed and the light should be wide from the front. Use the round tube where the line is seen from all sides: suspended runs, double-sided letters, freestanding accents. If the requirement is a flat face flush with the surface instead of a tube, that is the flat-emitting side-lit diffuser.

What the tube cannot do on its own is make a bad strip look even. Evenness along the run is set by the strip, its pitch and the distance to the diffusing wall; the tube controls how much of that light reaches the eye from each angle.

Three affiliated companies, one silicone chain

Extrusion is the last step of a chain we control from the compound up. The three companies below are affiliated; each does what it is set up for, and Yutian handles the profile you buy.

Guilin Yutian New Materials

silicone raw materials and auxiliary materials

Dongguan Huahong Rubber & Plastic Material Co., Ltd

compound development and mixing

Dongguan Yutian Silicone Rubber Technology Co., Ltd

extrusion, finishing and packing in our 6,800 m² plant in Changping, Dongguan

Why buyers place the profile with us

Compound in our own hands

Transmittance, colour and flexibility come from the compound. Because we compound and extrude, a change in the light effect is a formulation change, not a new supplier.

Extrusion from your drawing

We work from the section drawing or the groove you have to fill, and tell you whether an existing die fits or a new one is needed.

Finishing and accessories

Cut to length and packed to suit your line. Where the fixture needs a sealed end, the method is agreed before the order.

Paperwork that matches the claim

Certificates are described at the level they are held. Where a product-specific test report is needed, it is quoted as a separate project instead of implied.

Key advantages

Wide arc from a flat-backed profile

The D-shape keeps a narrow non-emitting back for mounting and sends the light over a wide arc from the front, so the line reads clean from normal viewing angles.

All-round, from any side

The round tube has no preferred viewing direction, which is what double-sided signage and suspended runs need.

Silicone through the wall

The diffusing wall is the extrusion itself: soft, flexible, stable under LED heat and sunlight, and it bends to a curve without cracking.

Sections sized for common strips

5 mm, 8 mm and 10 mm PCB cavities cover the strips most neon-flex fixtures use.

Optical performance set per project

We do not publish a fixed transmittance or uniformity figure. Evenness is confirmed on a sample with your strip, and that sample becomes the reference.

Service range −40 °C to +200 °C

The same compound covers outdoor facades and fixtures that run hot near the strip.

Sealed to IP67 or IP68 as an assembly

The tube is solid silicone; the rating belongs to the finished assembly, with the end treatment and sealing method agreed per project.

Cut to length, with matching accessories

Cut lengths and coils, packed so the run arrives ready to fit; the end treatment is agreed per project.

Available sections

The outside diameter sets the look; the cavity sets which strip fits. The LED counts in the last column are the strip densities each cavity is sized for — a compatibility range, not an optical rating.

VariantSectionOutside diameterPCB widthStrip compatibility
270° D-shapeD13Ø13 mm10 mmStrips from about 120 LEDs/m
270° D-shapeD20Ø20 mm5 mmStrips from about 120 LEDs/m
270° D-shapeD22Ø22 mm10 mmStrips from about 120 LEDs/m
360° roundR13Ø13 mm5 mm (double-sided PCB)Strips from about 120 LEDs/m
360° roundR18Ø18 mm5 mm (double-sided PCB)Strips from about 120 LEDs/m
360° roundR20Ø20 mm8 mmStrips from about 96 LEDs/m
360° roundR30Ø30 mm8 mmStrips from about 96 LEDs/m

A section outside this list is a die project, quoted before anything is cut. Existing sections need no new tooling.

270° D-shape compared with 360° round

The two variants share the compound and the extrusion process. The decision is about where the light has to be seen from and how the run is fixed.

Point270° D-shape360° round
Emitting arcAbout 270° over one face360° all round
Back of the profileFlat, sits against a surface or in a channelRound, needs a clip or a track to hold the run
View from behindNarrow non-emitting back, used for mountingSame as from the front
Sections in the rangeØ13, Ø20 and Ø22 mmØ13, Ø18, Ø20 and Ø30 mm
Strip cavity5 mm and 10 mm PCB widths5 mm (double-sided PCB) and 8 mm widths
Typical useWall grazing, cove, sign outlines, facade linesSuspended lines, double-sided signage, all-round accents

Technical specifications

PropertyValue
MaterialPlatinum-cured silicone, translucent opal
Hardness70 ± 5 Shore A (compound)
Density1.2 ± 0.1 g/cm³
Tensile strength≥ 8 MPa
Elongation at break≥ 300 %
Tear strength≥ 30 kN/m
Service temperature−40 °C to +200 °C
FlammabilityUL94 HB (compound level)
Restricted substancesROHS (raw-material level)
Light performanceEngineered per project; no fixed catalogue percentage
SealingIP67 or IP68 as a sealed assembly, depending on section, end treatment and method
SectionsØ13 to Ø30 mm; 270° D and 360° round
Coil lengthContinuous; cut to length, coil length confirmed per section

Values above describe the compound and the standard range. A dimension outside it, or an optical target, is a project confirmed on a sample and on the approval sheet.

Where this diffuser is used

Guidance from the geometry of the two profiles. We do not publish project references or client names; a sample length settles the fit.

Architectural outlines

Facade lines, wall grazing and cove details that follow the building.

Signage and channel letters

Even illumination across letters and logo outlines.

Retail and hospitality

Feature lines, shelving accents and bar fronts.

Suspended and freestanding runs

Round tube for lines seen from every side.

Landscape and facade accents

Outdoor lines where UV and heat both apply.

Exhibition and furniture

Curved detail lighting in joinery and stands.

Made to your specification

Six inputs are enough for a quotation and a sample proposal. The variant and the strip decide the section; the rest is finishing and packing.

  • Variant (270° D-shape or 360° round) and outside diameter
  • Strip width and the LED pitch you plan to run
  • Target effect: a tight line, a soft glow, or a specific brightness
  • IP requirement and the end-cap or sealing method you will use
  • Colour: opal white is standard; other tints are a compound project
  • Coil or cut lengths, and the packing you need

Minimum order value is USD 500. Unit price is quoted per project, because diameter, compound and cut length change with the strip.

Samples and lead time

Stock samples: free

Samples of standard stock items are sent free of charge, usually dispatched within 3 days.

Custom runs: quoted

A run in your compound, section or cut length is quoted with the project, including any die.

Production lead time

Standard items 5–7 days. Custom items 10–20 working days after sample approval.

Certificates and quality

The certificates below cover our compounds and our management system. They do not mean that every finished profile has been individually tested; a product-specific test report is a separate project and is quoted as one.

StandardWhat it coversLevel
ISO 9001:2015Quality management systemCompany level
ROHSRestricted substancesRaw-material level
REACHSubstance registrationRaw-material level
UL94 HBFlammability of the compoundRaw-material level
Class 100,000 cleanroomProduction environmentIn use

Monthly inspection pass rate is 95% or higher and batch acceptance pass rate is 99%.

Frequently asked questions

What does 270° or 360° actually describe?

The emitting arc around the tube. A 270° D-shape has a flat back that does not emit and sends light over about three quarters of the circumference; a 360° round tube emits all round. Neither is a lens angle; the diffusing wall is the silicone wall itself.

Which variant should I use?

If the run sits against a surface and is seen from the front, the D-shape gives a wider, cleaner line with a flat back for mounting. If the line is seen from all sides, or hangs free, the round tube is the right choice.

Will the line look even, without gaps between LEDs?

Evenness depends on the strip efficacy and LED pitch, the distance from strip to diffusing wall, and the transmittance of the compound. We build a sample with your strip and confirm it; a tube alone does not guarantee an even line for every strip.

Do you supply optical data?

The light effect is measured on the sample built for your project, and that approved sample becomes the reference. We do not publish catalogue transmittance or uniformity percentages, because they would not describe your strip.

Is the neon flex waterproof?

The tube is solid silicone. Where the fixture needs a rating it is supplied as a sealed assembly rated IP67 or IP68, depending on the section, the end treatment and sealing method.

What temperature and conditions can it take?

−40 °C to +200 °C, with UV exposure expected outdoors. If the fixture runs hotter, tell us and we will say whether a compound change is needed.

How long can a run be?

Runs are supplied as coils or cut lengths; the coil length is confirmed per section and packing, and the light output of the strip over a long run is a discussion we have before quoting.

What are the order terms?

Minimum order value USD 500. Stock samples are free; custom runs are quoted. Standard items ship in 5–7 days, custom items in 10–20 working days after sample approval.

Related silicone LED parts

The other silicone LED parts we make, and the guides that explain how the formats differ:

Browse the full LED silicone parts category for sleeves, profiles, neon flex and accessories.

Send the variant, the strip and the run length

Tell us whether the line is seen from one side or all round, which strip you plan to use, and how long the run is. We will confirm the section and propose a sample.

salesmanager@yutiansilicone.com · Mobile / WhatsApp +86 180 2892 1514
DongGuan Yutian Silicone Rubber Technology Co., Ltd
Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China
Silicone manufacturer since 2012

Silicone Neon Flex Diffuser, 270° D-Shape & 360° Round
Silicone neon flex diffuser, extruded in two emission angles: a 270° D-shape with a flat back for wall and sign outlines, and a 360° round tube that reads the same from every side. D-shape Ø13/Ø20/Ø22 mm, round Ø13/Ø18/Ø20/Ø30 mm, 5–10 mm strip cavities, −40 to +200 °C, IP67/IP68 as a sealed assembly.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Silicone Neon Flex Diffuser, 270° D-Shape & 360° Round

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.