Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

High Pressure Braid Reinforced Silicone Hose

Braid reinforced silicone hose: a platinum-cured silicone bore, a high-temperature braid and an outer silicone jacket bonded into one wall. The braid carries the hoop load, so the bore holds pressure and full vacuum without collapsing. Published burst 1.18–3.73 MPa by bore, −40 °C to +200 °C, ID 3–31.75 mm published sections.

    Product Features

    Braid reinforced silicone hose: a platinum-cured silicone bore, a high-temperature polyester braid and an outer silicone jacket, bonded into one wall
    The braid carries the hoop load: burst 1.18–3.73 MPa by bore, and the bore holds full vacuum without collapsing
    Working pressure = burst divided by your safety factor: 0.30–0.86 MPa at 4:1, 0.39–1.14 MPa at 3:1
    −40 °C to +200 °C continuous; 70 Shore A bore, 60 Shore A jacket, ≥8.6 MPa tensile, ≥360% elongation, ≥32 kN/m tear
    Eleven published sections from ID 3 to 31.75 mm, with burst figures and bend radii; other bores to order up to 50 mm
    Higher pressure quoted per project: mesh-braided and steel-wire-braided constructions are available as custom options with their own burst figure

    Application

    Coolant and hot water
    Engine, heater and equipment cooling loops under pressure and heat cycles.
    Pneumatic and air lines
    Compressed air and vacuum runs where a plain tube would balloon.
    Chemical and solvent transfer
    Platinum-cured bore, no peroxide residue, no plasticiser.
    Food and beverage
    FDA 21 CFR 177.2600, NSF/ANSI 51 and LFGB materials; smooth bore.
    Vacuum and suction
    Full vacuum without the bore collapsing into the flow path.
    Equipment OEM
    Repeatable bore, published burst figure and a fixed cut length.

  • Parameters

    Product Features

    Braid reinforced silicone hose: a platinum-cured silicone bore, a high-temperature polyester braid and an outer silicone jacket, bonded into one wall
    The braid carries the hoop load: burst 1.18–3.73 MPa by bore, and the bore holds full vacuum without collapsing
    Working pressure = burst divided by your safety factor: 0.30–0.86 MPa at 4:1, 0.39–1.14 MPa at 3:1
    −40 °C to +200 °C continuous; 70 Shore A bore, 60 Shore A jacket, ≥8.6 MPa tensile, ≥360% elongation, ≥32 kN/m tear
    Eleven published sections from ID 3 to 31.75 mm, with burst figures and bend radii; other bores to order up to 50 mm
    Higher pressure quoted per project: mesh-braided and steel-wire-braided constructions are available as custom options with their own burst figure

    Application

    Coolant and hot water
    Engine, heater and equipment cooling loops under pressure and heat cycles.
    Pneumatic and air lines
    Compressed air and vacuum runs where a plain tube would balloon.
    Chemical and solvent transfer
    Platinum-cured bore, no peroxide residue, no plasticiser.
    Food and beverage
    FDA 21 CFR 177.2600, NSF/ANSI 51 and LFGB materials; smooth bore.
    Vacuum and suction
    Full vacuum without the bore collapsing into the flow path.
    Equipment OEM
    Repeatable bore, published burst figure and a fixed cut length.
Yutian · braid reinforced silicone hose · platinum-cured

A braid reinforced silicone hose, built for pressure and vacuum

A braid reinforced silicone hose is a silicone tube with a high-temperature braid bonded between a platinum-cured bore and an outer silicone jacket. The braid takes the hoop load, so the bore stays round under pressure and does not collapse under vacuum, and the silicone keeps the hose flexible and clean from −40 °C to +200 °C.

Burst 1.18–3.73 MPa−40 °C to +200 °CID 3–31.75 mm publishedFull vacuumPolyester or aramid braid

What the braid does

An unreinforced silicone tube is soft: it bulges, then swells, then bursts. Adding a braid over the bore changes what the tube can do. The braid carries the hoop load, so pressure pushes against the braid instead of stretching the silicone wall. The same braid stops the wall from being sucked in when the line runs under vacuum. And because the braid holds the wall, the bore can stay thin: the hose stays flexible at the radius your routing needs.

The build is three layers, bonded in one extrusion and braiding run: a platinum-cured, high-transparency silicone bore; a high-temperature polyester braid (aramid and other yarns are available); and an outer silicone jacket that locks the braid in place and protects it from abrasion. Nominal hardness is 70 Shore A on the bore and 60 Shore A on the jacket; tensile strength is ≥ 8.6 MPa, elongation at break ≥ 360% and tear strength ≥ 32 kN/m on the specification sheet. The construction is described in more detail in how the three-layer polyester braid is built.

Not for human implantation.

Burst is what we publish — working pressure is yours to set

We publish the burst figure, measured as a minimum on a new hose. We do not publish a single working pressure for the whole range, because the right working pressure is the burst figure divided by the safety factor your process, standard or customer drawing requires. A line that carries water at 40 °C and a line that carries coolant next to a hot engine do not get the same factor.

So the table below is arithmetic, not a catalogue rating: the same burst figure divided by a 4:1 and a 3:1 safety factor. Tell us the factor your design uses and we quote against it.

ModelID (mm)Burst (MPa)Working at 4:1 (MPa)Working at 3:1 (MPa)
HJBX-0046.35≥ 3.430.861.14
HJBX-00712.7≥ 2.450.610.82
HJBX-00919.05≥ 1.770.440.59
HJBX-01131.75≥ 1.180.300.39

Worked examples from the published burst figures: divide by 4 or 3 for a conservative design, and check the temperature and the fluid with us before you fix the factor.

Two practical notes. First, pressure and temperature are not independent: the same hose is happier at 3 MPa and 20 °C than at 3 MPa and 180 °C, so a hot line is designed from the temperature first. Second, if your pressure target is above what the polyester build gives, the answer is a different construction — mesh-braided or steel-wire-braided hose can be quoted as a custom option for higher pressure and larger bores, and the burst figure is then quoted per project rather than taken from this table.

Sizes, burst figures and bend radii

These are the eleven sections we publish burst figures and bend radii for. The small bores take the most pressure: ID 3 mm bursts above 3.73 MPa, and the figure tapers to 1.18 MPa at ID 31.75 mm, because the wall and the braid carry more load on a small diameter.

ModelID (mm)OD (mm)Wall (mm)Burst (MPa)Bend radius (mm)
HJBX-0013 ± 0.58 ± 0.52.5≥ 3.7335
HJBX-0024 ± 0.59 ± 0.52.5≥ 3.7335
HJBX-0035 ± 0.511 ± 0.53≥ 3.7335
HJBX-0046.35 ± 0.512 ± 0.52.825≥ 3.4335
HJBX-0057.93 ± 0.515 ± 0.53.535≥ 3.4350
HJBX-0069.52 ± 0.517 ± 0.53.74≥ 3.4350
HJBX-00712.7 ± 0.722 ± 0.74.65≥ 2.4570
HJBX-00815.87 ± 0.725 ± 0.74.565≥ 2.2680
HJBX-00919.05 ± 0.731 ± 0.75.975≥ 1.77110
HJBX-01025.4 ± 0.738 ± 0.76.3≥ 1.18150
HJBX-01131.75 ± 0.746 ± 0.77.125≥ 1.18200

Burst values are minimums, given in MPa. Tolerances are ±0.5 mm up to ID 9.52 mm and ±0.7 mm above that. Each pack holds 1–15 m; cut lengths and coils are quoted per order.

Between the published sections, and up to ID 50 mm, the same construction is made to order: the bore is set at the die and the braid, so a size between models is a normal order rather than a tooling project. Above 50 mm the wall and the braid need a different set-up, and those lines are quoted per project.

Braid reinforced hose or plain silicone tube?

Both are silicone and both are clean, flexible and transparent. The braid is what changes the job the hose can do: it is the difference between a tube that carries fluid and a hose that holds pressure and vacuum without changing shape.

PropertyBraid reinforced hoseUnreinforced silicone tube
PressureBraid carries the hoop load; burst 1.18–3.73 MPa by boreBulges and bursts at low pressure
VacuumHolds full vacuum without the bore collapsingCollapses inward
KinkingResists kinking; bend radius published per modelKinks and closes under a tight bend
Nominal boreHolds its bore under pressure, so flow stays steadyBore grows under pressure
Wall thicknessThin wall possible, so the hose stays flexibleThick wall needed for strength
FlexibilityFlexible at 1.5 mm wall up to ID 50 mmStiff once the wall is thick enough

If the line runs at atmospheric pressure and you only need flexibility, a plain tube on the braided silicone hose range is simpler and cheaper. If the line sees pressure, vacuum, a pump pulse or a tight bend radius, the braided build is the one that keeps its bore.

Where a braid reinforced silicone hose is used

Coolant and hot water

Engine, heater and equipment cooling loops that see pressure, heat cycles and glycol.

Pneumatic and air lines

Compressed air and vacuum runs where a plain tube would balloon or collapse.

Chemical and solvent transfer

Platinum-cured bore, no peroxide residue and no plasticiser, so the medium stays clean.

Food and beverage

Material compliance to FDA 21 CFR 177.2600, NSF/ANSI 51 and LFGB, with a smooth, cleanable bore.

Vacuum and suction

Full vacuum without the bore collapsing, which is the usual reason a buyer moves from tube to braided hose.

Equipment OEM

Machine builders who need a repeatable bore, a published burst figure and a fixed cut length.

The same hose also goes into steam lines, automotive heater and coolant parts, and food equipment; those are covered on the braided steam hose page and the automotive braided silicone hose page.

Three affiliated companies, one silicone chain

The hose is the last step of a chain we control from the compound up: raw material, compounding and the finished hose are handled by three affiliated companies, and Yutian ships the hose you buy.

Guilin Yutian New Materials

Silicone raw material and compound development, 28,000 m² site.

Dongguan Huahong Rubber and Plastic

Compounding, auxiliaries and batch control before extrusion.

Dongguan Yutian Silicone

Braiding, extrusion and finishing in a 6,800 m² plant.

What you can specify

Braid yarn

Polyester is the standard. Aramid is available for the hotter end of the range, and cotton or nylon for other duties. Burst figures are published for the polyester build.

Bore, wall and length

ID 3–50 mm to order, wall from 1.5 mm up, cut to length or coiled, with the ends bare for your own end treatment.

Colour

Transparent is standard. Opaque and tinted compounds follow a Pantone reference.

Higher pressure

Mesh-braided and steel-wire-braided constructions are available as custom options for higher pressure and larger bores; those are quoted per project with their own burst figure.

Two notes that save a round of samples. First, the braid is what carries the burst load, so a pressure target is met by changing the braid and the wall, not by thickening the bore. Second, a burst figure is not a working rating: tell us your safety factor, the fluid and the temperature, and the quote will carry the working pressure for your line.

Lead time, samples and tooling

Published sections

Ship in 5 to 7 working days from stock compounds.

Samples

Stock samples leave in 3 days and are free; freight is paid by the buyer.

Custom construction

10 to 20 working days, depending on the yarn and the end treatment.

Tooling

A bore or construction outside the published sections is quoted per project, with tooling at USD 100–400 per product.

Materials, documents and limits

Material compliance: FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS. The plant runs an ISO 9001 and ISO 13485 quality system, and ISO 10993 biocompatibility reports are issued on request. Certificates travel with the shipment; third-party testing is arranged when your process needs a report rather than a certificate.

Limits worth stating up front: this is a silicone hose, not a hydraulic hose, and it is not for human implantation. Where a drawing calls for a high-pressure hydraulic or fuel line, the material is the wrong one and we will say so.

The hose is extruded, braided and jacketed on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, at a monthly capacity of up to 8 million metres, since 2012.

Questions buyers ask before they specify

What is the working pressure?

We publish the burst figure: 1.18–3.73 MPa depending on the bore. Working pressure is the burst figure divided by the safety factor your process or drawing requires — at 4:1 that is 0.30–0.86 MPa, at 3:1 it is 0.39–1.14 MPa. Tell us the factor and we quote against it.

Is the burst figure a rating?

No. It is the minimum pressure at which a new hose is destroyed, measured per bore. A line is designed on working pressure, which is the burst figure divided by the safety factor, and that is why we ask for the factor rather than publishing one number for the whole range.

Can it take vacuum?

Yes. The braid carries the load instead of the wall, so the bore can be drawn to full vacuum without collapsing. That is the usual reason buyers move from a plain tube to a braided hose.

What temperature range?

−40 °C to +200 °C continuous. The aramid braid is the option for the top of that range; the polyester build is the standard and is what the published burst figures refer to.

What is the braid made of?

Polyester is standard, with aramid available for the hotter end of the range and cotton or nylon for other duties. The braid is bonded between the bore and the jacket, so the bore stays smooth and cleanable.

Which sizes do you publish figures for?

Eleven sections, ID 3 mm to 31.75 mm, each with a burst figure and a bend radius. Bores between those sections, and up to 50 mm, are made to order; above 50 mm is quoted per project.

Can you make a higher pressure version?

For pressure above the polyester build, mesh-braided and steel-wire-braided constructions are available as custom options and are quoted per project with their own burst figure. Tell us the working pressure and the bore and we will say which construction fits.

What is the lead time and can I get a sample?

Published sections ship in 5 to 7 working days, and stock samples leave in 3 days. Custom constructions take 10 to 20 working days. Stock samples are free; freight is paid by the buyer.

Need a braid reinforced silicone hose for a pressure line?

Send the bore, the working pressure or the safety factor, the fluid and the temperature. You get the model, the burst figure and a sample date back.

Request a quote

WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com

High Pressure Braid Reinforced Silicone Hose
Braid reinforced silicone hose: a platinum-cured silicone bore, a high-temperature braid and an outer silicone jacket bonded into one wall. The braid carries the hoop load, so the bore holds pressure and full vacuum without collapsing. Published burst 1.18–3.73 MPa by bore, −40 °C to +200 °C, ID 3–31.75 mm published sections.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

High Pressure Braid Reinforced Silicone Hose

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.