Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

PRODUCTS


Specializing in the production of highquality silicone rubber products

PRODUCT


Specializing in the production of highquality silicone rubber products

— Product Categories

— News Recommended

— Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Automotive Braided Silicone Hose

Automotive braided silicone hose: a platinum-cured silicone bore, a high-temperature braid and an outer silicone jacket, in eleven imperial bores from 1/8" to 1¼" (ID 3–31.75 mm), with other bores to order up to 50 mm. −40 to +200 °C, burst 1.18–3.73 MPa, supplied coiled or cut to length to automotive parts makers and hose assemblers.

    Product Features

    Automotive braided silicone hose: a platinum-cured silicone bore, a high-temperature braid and an outer silicone jacket, bonded into one wall
    Imperial bores: 1/8" to 1¼" (ID 3–31.75 mm) published with burst figures; other bores to order up to 50 mm
    −40 °C to +200 °C continuous, with polyester or aramid braid and 70 Shore A bore / 60 Shore A jacket
    Burst 1.18–3.73 MPa by bore; working pressure is set per project by the part's safety factor
    Written for parts makers: hose supplied coiled or cut to length with bare ends, ready for your own crimp, mould or clamp
    Component supply, stated honestly: material-level FDA/LFGB/NSF/REACH/RoHS documents and ISO 9001 and ISO 13485 systems; IATF 16949 stays with the assembler

    Application

    Heater core lines
    Feed and return runs to the heater core that stay flexible while hot.
    Coolant bypass and return
    Small-bore coolant runs on the engine and expansion tank.
    Vacuum and emissions
    Vacuum, PCV and evaporative lines that resist heat soak and oil vapour.
    Washer and air lines
    Washer feed and air suspension lines, cut to length and coiled.
    Motorcycle and powersport
    Compact cooling loops where rubber would harden or crack.
    EV thermal loops
    Battery and motor cooling circuits that need a clean, documented bore.

  • Parameters

    Product Features

    Automotive braided silicone hose: a platinum-cured silicone bore, a high-temperature braid and an outer silicone jacket, bonded into one wall
    Imperial bores: 1/8" to 1¼" (ID 3–31.75 mm) published with burst figures; other bores to order up to 50 mm
    −40 °C to +200 °C continuous, with polyester or aramid braid and 70 Shore A bore / 60 Shore A jacket
    Burst 1.18–3.73 MPa by bore; working pressure is set per project by the part's safety factor
    Written for parts makers: hose supplied coiled or cut to length with bare ends, ready for your own crimp, mould or clamp
    Component supply, stated honestly: material-level FDA/LFGB/NSF/REACH/RoHS documents and ISO 9001 and ISO 13485 systems; IATF 16949 stays with the assembler

    Application

    Heater core lines
    Feed and return runs to the heater core that stay flexible while hot.
    Coolant bypass and return
    Small-bore coolant runs on the engine and expansion tank.
    Vacuum and emissions
    Vacuum, PCV and evaporative lines that resist heat soak and oil vapour.
    Washer and air lines
    Washer feed and air suspension lines, cut to length and coiled.
    Motorcycle and powersport
    Compact cooling loops where rubber would harden or crack.
    EV thermal loops
    Battery and motor cooling circuits that need a clean, documented bore.
Yutian · braided silicone hose · imperial automotive sizes

A braided silicone hose for automotive parts makers

A braided silicone hose for automotive use is a three-layer hose: a platinum-cured silicone bore, a high-temperature braid and an outer silicone jacket. We make the hose; our customers are the parts manufacturers and hose assemblers who mould, bond or clamp the ends and sell the finished line. The braid carries the pressure, the silicone keeps it flexible from −40 °C to +200 °C, and there is no rubber and no plasticiser in the build.

ID 3–31.75 mm (1/8"–1¼")−40 °C to +200 °CBurst 1.18–3.73 MPaPolyester or aramid braidSold by the metre or cut length

What a braided silicone automotive hose is

Three layers are bonded in one extrusion and braiding run. The bore is a platinum-cured, high-transparency silicone tube; the middle is a high-temperature braid that takes the hoop load; the jacket is silicone again, so the braid is protected from abrasion and from the road environment. Nothing in the build is rubber, so the hose does not crack the way an EPDM coolant hose does after years of heat cycles, and the bore does not shed plasticiser into the coolant.

Nominal hardness is 70 Shore A on the bore and 60 Shore A on the jacket. Tensile strength is ≥ 8.6 MPa, elongation at break ≥ 360% and tear strength ≥ 32 kN/m on the specification sheet. The construction is described in more detail in how the three-layer polyester braid is built.

The hose is a component, not a finished vehicle part. It is supplied coiled or cut to length, with the ends bare, so the parts maker can mould, crimp or clamp the final assembly and take the vehicle-level validation.

Why silicone instead of EPDM on a coolant or heater line?

Both materials are used on cars. The choice usually turns on how hot the line runs, how long the vehicle is expected to last, and what the coolant is allowed to pick up. EPDM is cheaper and is the default on volume production; silicone is chosen where the line runs hot, where the part has to stay flexible in service, or where a transparent bore helps the parts maker or the aftermarket brand show quality.

PropertyBraided silicone hoseEPDM automotive hose
Temperature range−40 °C to +200 °C continuousAbout −40 °C to +120 °C in coolant duty
Hot flexibilityStays flexible, no hardening after heat cyclesHardens and cracks over time
AgeingColour and hardness hold; no cracking at the endsCracks at the ends first, then leaks
Coolant and glycolUnaffected by glycol coolant, no plasticiser to leachPlasticiser can migrate into the coolant
Ozone and UVSilicone is not attacked by ozoneNeeds protection in harsh exposure
Bore surfaceSmooth, transparent, so flow and contamination stay visibleUsually black; bore not visible
PressurePolyester braid carries the burst load, 1.18–3.73 MPa by boreHigher-pressure grades exist
CostHigher material cost, longer service intervalCheaper per metre

The practical rule from our side of the supply chain: below 150 °C and on a cost-driven part, EPDM is often the right answer. Above that, or on a hose that has to keep its geometry after a thousand heat cycles, silicone is the usual choice, and the braid is what lets the wall stay thin while the hose still takes pressure.

Where the hose goes

Heater core lines

Feed and return runs from the engine or HVAC unit to the heater core, where the hose has to stay flexible while hot and not harden at the clamped ends.

Coolant bypass and return

Small-bore coolant runs on the engine, expansion tank and thermostat housing, where a braided wall holds pressure without a thick wall section.

Vacuum and emissions lines

Vacuum runs, PCV and evaporative lines where the bore has to stay clean and the hose has to resist oil vapour and heat soak.

Washer and air lines

Washer feed, air suspension and small air lines on vehicles and trailers, cut to length and coiled for the assembler.

Motorcycle and powersports

Coolant loops on bikes, quads and side-by-sides, where the compact bends and the temperature swing rule out a rubber hose.

EV thermal loops

Battery and motor cooling circuits, where a non-conductive silicone wall and a clean bore are easier to document than a rubber hose.

These are the uses our customers build the hose into. We do not supply the finished assembly and we do not tool the end fittings: the parts maker chooses the connector, the crimp or the moulded end.

Sizes: the eleven published sections are the imperial sizes

The eleven sections below are the ones we publish burst figures and bend radii for, and they land on the imperial sizes an automotive line is usually drawn in — 1/8", 5/32", 3/16", 1/4", 5/16", 3/8", 1/2", 5/8", 3/4", 1" and 1¼". That is not a coincidence: these are the bores our automotive customers order most often.

ModelID (mm)ID (inch)OD (mm)Wall (mm)Burst (MPa)Bend radius (mm)
HJBX-0013 ± 0.51/8"8 ± 0.52.5≥ 3.7335
HJBX-0024 ± 0.55/32"9 ± 0.52.5≥ 3.7335
HJBX-0035 ± 0.53/16"11 ± 0.53≥ 3.7335
HJBX-0046.35 ± 0.51/4"12 ± 0.52.825≥ 3.4335
HJBX-0057.93 ± 0.55/16"15 ± 0.53.535≥ 3.4350
HJBX-0069.52 ± 0.53/8"17 ± 0.53.74≥ 3.4350
HJBX-00712.7 ± 0.71/2"22 ± 0.74.65≥ 2.4570
HJBX-00815.87 ± 0.75/8"25 ± 0.74.565≥ 2.2680
HJBX-00919.05 ± 0.73/4"31 ± 0.75.975≥ 1.77110
HJBX-01025.4 ± 0.71"38 ± 0.76.3≥ 1.18150
HJBX-01131.75 ± 0.71¼"46 ± 0.77.125≥ 1.18200

Burst values are minimums, given in MPa. Tolerances are ±0.5 mm up to ID 9.52 mm and ±0.7 mm above that. Each pack holds 1–15 m; cut lengths and coils are quoted per order.

Between the published sections, and up to ID 50 mm, the same three-layer construction is made to order: the bore is set at the die and the braid, so a size between models is a normal order rather than a tooling project. Above 50 mm the wall and the braid need a different set-up, and those lines are quoted per project.

How we fit into an automotive supply chain

We are a hose component supplier, not a certified automotive parts manufacturer. The automotive qualification — IATF 16949, PPAP, part-level validation and the drawing that names the part — sits with the parts maker who moulds, bonds or clamps the hose into the vehicle part. That is the customer we supply.

Hose assemblers

Buy the hose coiled or cut, add the fittings and sell the finished line under their own part number.

Parts manufacturers

Mould or bond the hose into a heater, coolant or air assembly, and hold the OEM approval on the finished component.

Aftermarket brands

Specify the bore, wall, braid and colour, and pack the hose as a replacement part.

Documentation we can supply

Material-level compliance (FDA, LFGB, NSF, REACH, RoHS), ISO 9001 and ISO 13485 quality systems, and batch records for the hose in your order.

If your drawing calls for IATF 16949 on the hose itself, we are not the right supplier and we will say so at quotation. If your drawing calls for a documented silicone hose that your plant qualifies and assembles, that is exactly what we do.

What you can specify

Braid yarn

Polyester is standard. Aramid is available for the hotter end of the range, and cotton or nylon for other duties. Burst figures are published for the polyester build.

Bore, wall and length

ID 3–50 mm to order, wall from 1.5 mm up, cut to length or coiled, with the cut ends bare for your own end treatment.

Colour

Transparent is standard. Opaque and tinted compounds follow a Pantone reference, which is how most aftermarket lines are colour-coded.

Wall and reinforcement

The braid density and the jacket wall can be set for the bend radius your routing needs, and for the abrasion the line sees.

Two notes that save a round of samples. First, a hose that is correct at 200 °C in still air is not automatically correct for 200 °C coolant under pressure: the fluid, the duty cycle and the fitting decide together. Second, the braid is what carries the burst load, so a pressure target is met by changing the braid and the wall, not by adding a thicker bore.

Other constructions in the same family are on the braided silicone hose range, the aramid and high-temperature builds on the high-temperature braided range, and steam duty on the braided steam hose page.

Lead time, samples and tooling

Published sections

Ship in 5 to 7 working days from stock compounds.

Samples

Stock samples leave in 3 days and are free; freight is paid by the buyer.

Custom construction

10 to 20 working days, depending on the yarn and the end treatment.

Tooling

A bore or construction outside the published sections is quoted per project, with tooling at USD 100–400 per product.

Materials, documents and limits

Material compliance: FDA 21 CFR 177.2600, NSF/ANSI 51, LFGB, REACH and RoHS. The plant runs an ISO 9001 and ISO 13485 quality system, and ISO 10993 biocompatibility reports are issued on request. Certificates travel with the shipment; third-party testing is arranged when your process needs a report rather than a certificate.

Limits worth stating up front: the hose is a silicone component, not a fuel hose, and it is not for human implantation. Where a drawing calls for a fuel, oil-pressure or brake line, the material is the wrong one and we will say so.

The hose is extruded, braided and jacketed on 14 extrusion lines, 4 calendering lines and 7 moulding presses in a Class 100,000 cleanroom, at a monthly capacity of up to 8 million metres, since 2012.

Questions buyers ask before they specify

Do you hold IATF 16949?

No. We supply the hose to automotive parts manufacturers, and the automotive qualification — IATF 16949, PPAP and part-level validation — sits with the parts maker who assembles the hose into the vehicle part. What we provide is material-level compliance, ISO 9001 and ISO 13485 systems, and batch records for the hose you buy.

Which sizes are available in inches?

The eleven published sections cover 1/8", 5/32", 3/16", 1/4", 5/16", 3/8", 1/2", 5/8", 3/4", 1" and 1¼" bore, which is ID 3 mm to 31.75 mm. Bores between those sections, and up to 50 mm, are made to order.

What pressure does it take?

The burst column is a minimum, measured on a new hose: 3.73 MPa on the small bores, 1.18 MPa at ID 31.75 mm. Working pressure is the burst figure divided by the safety factor your part validation requires, so we quote it per project rather than publishing one number.

What temperature range?

−40 °C to +200 °C continuous. The aramid braid is the option for the top of that range; the polyester build is the standard and is what the published burst figures refer to.

Why silicone instead of EPDM?

EPDM is cheaper and fine on a cool line. Silicone is chosen where the line runs hot, where the hose has to stay flexible after many heat cycles, or where a transparent bore and no plasticiser in the coolant matter to the parts maker.

Can you cut to length and coil?

Yes. Standard packs hold 1–15 m, and cut lengths, coils and end-marking are quoted per order. The ends arrive bare so your plant can mould, crimp or clamp them.

Can the braid be aramid?

Yes. Aramid is available for the hotter end of the range, with polyester as the standard yarn and cotton or nylon for other duties. Pressure is quoted for the polyester build.

What is the lead time and can I get a sample?

Published sections ship in 5 to 7 working days, and stock samples leave in 3 days. Custom constructions take 10 to 20 working days. Stock samples are free; freight is paid by the buyer.

Need a braided silicone hose for an automotive part?

Send the bore in mm or inches, the coolant or air duty, the temperature and the length you need. You get the model, the burst figure and a sample date back.

Request a quote

WhatsApp +86 18028921514 · salesmanager@yutiansilicone.com

Automotive Braided Silicone Hose
Automotive braided silicone hose: a platinum-cured silicone bore, a high-temperature braid and an outer silicone jacket, in eleven imperial bores from 1/8" to 1¼" (ID 3–31.75 mm), with other bores to order up to 50 mm. −40 to +200 °C, burst 1.18–3.73 MPa, supplied coiled or cut to length to automotive parts makers and hose assemblers.
Long press to look detail
Long by picture save/share
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Automotive Braided Silicone Hose

Contact Us Now
INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Message

Hi!If you are looking for custom-made silicone rubber products, feel free to ask me any questions.

图片展示
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

    CONTACT


    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile:
    • 0086-18028921514
    • Fax:0086-769-82555312
    • Email:salesmanager@yutiansilicone.com

    Link: China Edge-lit Lighting, Backlight Lighting Manufa

    Contact Us

    Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

     

    • Mobile/Whatsapp:
      0086-18028921514
    • Fax:86-769-89221009
    • Email:salesmanager@yutiansilicone.com

     

    Copyright © 2015-2026 All Rights Reserved.

    Copyright © 2015-2026 All Rights Reserved.   

    Service Center

    Please choose online customer service to communicate

    Contacts
    Phone
    +8618028921514
    Service time
    From Monday to Sunday
    E-mail
    salesmanager@yutiansilicone.com
    Scan a QR Code
    Qrcode
    WhatsApp
    Add WeChat friend to learn more about the product
    Use Enterprise WeChat
    "Scan" to join the group chat
    Copy success!
    Add WeChat friend to learn more about the product
    I see.