Demand Submission
Please leave us a message and we will contact you within 24 hours
APPLICATION
Our silicone products are used in all walks of life
APPLICATION
Our silicone products are used in all walks of life
2026-10-27 12:54:08
Click:
Silicone neon flex for channel letters is a platinum-cured, translucent silicone extrusion that carries an LED strip inside a diffusing body, so a letter face reads as one continuous line with no visible dots. Sign makers specify it by section, cavity width and bending radius rather than by output figures.
| ManufacturingSince 2012 | FPC range4–28 mm | Temperature−40 to +200 °C | Capacity14 extrusion lines |
Silicone neon flex for channel letters replaces a glass tube and its electrodes with a flexible diffusing body, so the face reads as one continuous line instead of a row of components. It goes into face-lit letters, into halo-lit returns where the light washes the backer, and into shallow letters where a gas tube will not fit. Sign makers specify it for three reasons: a dot-free face, a body that holds a bend without a heat step, and one material family for interior and exterior letters alike. The channel letter section range is the starting point for a first quote.
The platform is 15 cross-sections from 6 × 11 mm to 100 × 30 mm, with a strip cavity from 6 mm to 30 mm. These are the values to draw against, and they appear on the quotation.
| Parameter | Specification |
|---|---|
| Cross-sections | 15 profiles, 6 × 11 mm to 100 × 30 mm |
| Strip cavity width | 6 mm to 30 mm |
| Twin-strip section | 100 × 30 mm, two parallel strip runs |
| Multicolor sections | 16 × 16 mm with four color zones; 25 × 15 mm with three |
| Strip compatibility | FPC 4 mm to 28 mm; PCB 8, 10 or 12 mm stocked |
| Inner cavity | 2.8 mm high, 8.8 mm to 13 mm wide |
| Two-color cavity | 2.5 mm to 2.9 mm high, 11 mm to 13 mm wide |
| Wall on the emitting face | 0.5 mm to 0.6 mm |
| Compound | Platinum-cured translucent silicone, 70 ± 5 Shore A, density 1.2 ± 0.1 g/cm³ |
| Mechanical values | Tensile strength ≥8 MPa, tear strength ≥30 kN/m |
| Working temperature | −40 to +200 °C |
| Coil basis | Square, groove, D and U at 200 m per roll; aluminum-channel cover at 100 m per roll |
Measure the loaded strip, not the drawing. Stocked PCB widths are 8, 10 and 12 mm and the FPC platform runs from 4 mm to 28 mm, so the cavity has to clear the widest point once the components and solder joints are on the strip. Standard inner width runs from 8.8 mm to 13 mm at 2.8 mm inner height, with a wall of 0.5 mm to 0.6 mm on the emitting face; two-color bodies sit at 2.5 mm to 2.9 mm inner height and 11 mm to 13 mm inner width. Across the 15 sections the cavity range is 6 mm to 30 mm. Too tight and the strip pinches at a bend; too loose and it rides up as a bright band through the diffuser.
A face-lit letter puts the section against the face, so the emitting face is the letter face and the job is an even wash at the distance the viewer stands. A top-view section with a flat emitting face suits that: the strip sits parallel to the acrylic and the face carries the rest. A halo-lit letter wants the opposite: the section mounts behind the return and throws light onto the backer, so a round, D or square section that follows the return line is the usual choice. Multicolor bodies at 16 × 16 mm with four color zones and 25 × 15 mm with three cover two-tone faces. The multicolor side-emitting range lists those sections against their cavity widths.
The section sets the radius, not the letter drawing. A silicone body bends without a heat step, but each section has a radius it follows comfortably in its bending plane, and a taller section needs a larger radius for the same curve. Two rules settle most letters. Bend in one plane: a section that has to turn in two directions needs a joint or a different mounting. Then mark the smallest radius and the bend direction on the drawing, because the same section follows one direction and fights the other. Where the artwork is tighter than the section allows, the letter is built in segments with bonded corners at the drawing stage.
Coil length follows the section: square, groove, D and U sections come at 200 m per roll, and the aluminum-channel cover at 100 m per roll. Quote from the cut list: the same metres cut into 2 m lengths and left on a coil are packed differently and priced differently. Bonded corners and closed ends appear as their own line.
An outdoor letter is settled by three inputs: the temperature it will see, the way the cut ends are closed, and the documentation the project file asks for. The body is rated from −40 to +200 °C and is resistant to yellowing under normal LED operating temperatures. The compound holds its color and flexibility across that range; the strip and end cap decide the rest, since an open cut end lets water track along the cavity. Material certificates for ROHS, REACH and UL94 HB are held at material level, and a finished-goods report is arranged per project. The silicone sleeve for LED strip range covers the cased form where the strip is fitted on site.
Yes. The 15 sections are the stocked platform; a new one is drawn from a sketch that fixes the outer size, the cavity and the emitting face. Standard round sections and common profiles carry no mould fee; a new cross-section is quoted per project, with the tooling assessed from the drawing and shown as its own line. Two-color construction is a co-extrusion step, so it is quoted as its own line as well. Silicone parts are produced in-house; aluminum profiles, end caps and clips are integrated through partner suppliers. Behind that sit 14 extrusion lines, a 6,800 m² facility and monthly capacity up to 8,000,000 meters.
Describe the look rather than a figure. Two sections can share a 2.8 mm inner height and still read differently, because the compound and the strip-to-face distance decide what the viewer sees. Milky and clear are different compounds, transmittance is adjusted through compound formulation, and the output of a finished letter is engineered per project against the chosen strip. Say which effect matters most: dot hiding at close range, color trueness on a brand color, or maximum output across a large face.
A quotation names the section, the cavity and the coil basis, then states the price per metre or per piece and which applies. Minimum order value: USD 500, measured on value rather than metres. Lead time follows the order type: standard items 5–7 days, in-stock samples 3 days, other custom work 10–20 working days. Where end caps or a channel are integrated through partner suppliers, the later schedule sets the delivery date.
The smallest standard section is 6 × 11 mm, which suits a shallow letter where a deeper body would stand proud of the return. It takes a single strip run, and it is the section that follows the tightest bend in the range.
An 8 mm strip is a stocked PCB width, and the standard cavity family it sits in measures 8.8 mm to 13 mm inner width at 2.8 mm inner height. That leaves the strip room to lie flat without pinching at a bend. Send the component height too, since 2.8 mm is what the loaded strip has to clear.
It depends on the section: the four standard sections ship at 200 m per roll, while the aluminum-channel cover runs at 100 m per roll. Cut lengths are quoted from the cut list, so send both the total metres and the length each piece has to be cut to.
Silicone parts are extruded in-house, while aluminum profiles, end caps and clips are integrated through partner suppliers and can ship as a fitted set. State whether the order is the extrusion alone or an assembly, because an assembly needs the interface dimension and carries a second schedule.
Minimum order value: USD 500, measured on value rather than metres. Standard items ship in 5–7 days, in-stock samples in 3 days, and other custom work takes 10–20 working days. Where a channel is integrated through a partner supplier, the later schedule sets the date.
Send the letter drawing or a sketch with the cavity and the emitting face marked, the strip width and component height, the cut list, and whether the letter is face-lit or halo-lit. Two of those five are usually missing on a first enquiry, and a partial reply is still faster than a finished drawing.
Ready to specify a channel letter run?
Send the letter drawing, the strip width and the face-lit or halo-lit call — a stocked section from 6 × 11 mm to 100 × 30 mm, or a new cross-section drawn from your sketch.
DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.
Products Recommended

Silicone neon flex for channel letters is a platinum-cured, translucent silicone extrusion that carries an LED strip inside a diffusing body, so a letter face reads as one continuous line with no visible dots. Sign makers specify it by section, cavity width and bending radius rather than by output figures.
| ManufacturingSince 2012 | FPC range4–28 mm | Temperature−40 to +200 °C | Capacity14 extrusion lines |
Silicone neon flex for channel letters replaces a glass tube and its electrodes with a flexible diffusing body, so the face reads as one continuous line instead of a row of components. It goes into face-lit letters, into halo-lit returns where the light washes the backer, and into shallow letters where a gas tube will not fit. Sign makers specify it for three reasons: a dot-free face, a body that holds a bend without a heat step, and one material family for interior and exterior letters alike. The channel letter section range is the starting point for a first quote.
The platform is 15 cross-sections from 6 × 11 mm to 100 × 30 mm, with a strip cavity from 6 mm to 30 mm. These are the values to draw against, and they appear on the quotation.
| Parameter | Specification |
|---|---|
| Cross-sections | 15 profiles, 6 × 11 mm to 100 × 30 mm |
| Strip cavity width | 6 mm to 30 mm |
| Twin-strip section | 100 × 30 mm, two parallel strip runs |
| Multicolor sections | 16 × 16 mm with four color zones; 25 × 15 mm with three |
| Strip compatibility | FPC 4 mm to 28 mm; PCB 8, 10 or 12 mm stocked |
| Inner cavity | 2.8 mm high, 8.8 mm to 13 mm wide |
| Two-color cavity | 2.5 mm to 2.9 mm high, 11 mm to 13 mm wide |
| Wall on the emitting face | 0.5 mm to 0.6 mm |
| Compound | Platinum-cured translucent silicone, 70 ± 5 Shore A, density 1.2 ± 0.1 g/cm³ |
| Mechanical values | Tensile strength ≥8 MPa, tear strength ≥30 kN/m |
| Working temperature | −40 to +200 °C |
| Coil basis | Square, groove, D and U at 200 m per roll; aluminum-channel cover at 100 m per roll |
Measure the loaded strip, not the drawing. Stocked PCB widths are 8, 10 and 12 mm and the FPC platform runs from 4 mm to 28 mm, so the cavity has to clear the widest point once the components and solder joints are on the strip. Standard inner width runs from 8.8 mm to 13 mm at 2.8 mm inner height, with a wall of 0.5 mm to 0.6 mm on the emitting face; two-color bodies sit at 2.5 mm to 2.9 mm inner height and 11 mm to 13 mm inner width. Across the 15 sections the cavity range is 6 mm to 30 mm. Too tight and the strip pinches at a bend; too loose and it rides up as a bright band through the diffuser.
A face-lit letter puts the section against the face, so the emitting face is the letter face and the job is an even wash at the distance the viewer stands. A top-view section with a flat emitting face suits that: the strip sits parallel to the acrylic and the face carries the rest. A halo-lit letter wants the opposite: the section mounts behind the return and throws light onto the backer, so a round, D or square section that follows the return line is the usual choice. Multicolor bodies at 16 × 16 mm with four color zones and 25 × 15 mm with three cover two-tone faces. The multicolor side-emitting range lists those sections against their cavity widths.
The section sets the radius, not the letter drawing. A silicone body bends without a heat step, but each section has a radius it follows comfortably in its bending plane, and a taller section needs a larger radius for the same curve. Two rules settle most letters. Bend in one plane: a section that has to turn in two directions needs a joint or a different mounting. Then mark the smallest radius and the bend direction on the drawing, because the same section follows one direction and fights the other. Where the artwork is tighter than the section allows, the letter is built in segments with bonded corners at the drawing stage.
Coil length follows the section: square, groove, D and U sections come at 200 m per roll, and the aluminum-channel cover at 100 m per roll. Quote from the cut list: the same metres cut into 2 m lengths and left on a coil are packed differently and priced differently. Bonded corners and closed ends appear as their own line.
An outdoor letter is settled by three inputs: the temperature it will see, the way the cut ends are closed, and the documentation the project file asks for. The body is rated from −40 to +200 °C and is resistant to yellowing under normal LED operating temperatures. The compound holds its color and flexibility across that range; the strip and end cap decide the rest, since an open cut end lets water track along the cavity. Material certificates for ROHS, REACH and UL94 HB are held at material level, and a finished-goods report is arranged per project. The silicone sleeve for LED strip range covers the cased form where the strip is fitted on site.
Yes. The 15 sections are the stocked platform; a new one is drawn from a sketch that fixes the outer size, the cavity and the emitting face. Standard round sections and common profiles carry no mould fee; a new cross-section is quoted per project, with the tooling assessed from the drawing and shown as its own line. Two-color construction is a co-extrusion step, so it is quoted as its own line as well. Silicone parts are produced in-house; aluminum profiles, end caps and clips are integrated through partner suppliers. Behind that sit 14 extrusion lines, a 6,800 m² facility and monthly capacity up to 8,000,000 meters.
Describe the look rather than a figure. Two sections can share a 2.8 mm inner height and still read differently, because the compound and the strip-to-face distance decide what the viewer sees. Milky and clear are different compounds, transmittance is adjusted through compound formulation, and the output of a finished letter is engineered per project against the chosen strip. Say which effect matters most: dot hiding at close range, color trueness on a brand color, or maximum output across a large face.
A quotation names the section, the cavity and the coil basis, then states the price per metre or per piece and which applies. Minimum order value: USD 500, measured on value rather than metres. Lead time follows the order type: standard items 5–7 days, in-stock samples 3 days, other custom work 10–20 working days. Where end caps or a channel are integrated through partner suppliers, the later schedule sets the delivery date.
The smallest standard section is 6 × 11 mm, which suits a shallow letter where a deeper body would stand proud of the return. It takes a single strip run, and it is the section that follows the tightest bend in the range.
An 8 mm strip is a stocked PCB width, and the standard cavity family it sits in measures 8.8 mm to 13 mm inner width at 2.8 mm inner height. That leaves the strip room to lie flat without pinching at a bend. Send the component height too, since 2.8 mm is what the loaded strip has to clear.
It depends on the section: the four standard sections ship at 200 m per roll, while the aluminum-channel cover runs at 100 m per roll. Cut lengths are quoted from the cut list, so send both the total metres and the length each piece has to be cut to.
Silicone parts are extruded in-house, while aluminum profiles, end caps and clips are integrated through partner suppliers and can ship as a fitted set. State whether the order is the extrusion alone or an assembly, because an assembly needs the interface dimension and carries a second schedule.
Minimum order value: USD 500, measured on value rather than metres. Standard items ship in 5–7 days, in-stock samples in 3 days, and other custom work takes 10–20 working days. Where a channel is integrated through a partner supplier, the later schedule sets the date.
Send the letter drawing or a sketch with the cavity and the emitting face marked, the strip width and component height, the cut list, and whether the letter is face-lit or halo-lit. Two of those five are usually missing on a first enquiry, and a partial reply is still faster than a finished drawing.
Ready to specify a channel letter run?
Send the letter drawing, the strip width and the face-lit or halo-lit call — a stocked section from 6 × 11 mm to 100 × 30 mm, or a new cross-section drawn from your sketch.
DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.
Products Recommended

Products Recommended
Products Recommended
