Demand Submission
Please leave us a message and we will contact you within 24 hours
APPLICATION
Our silicone products are used in all walks of life
APPLICATION
Our silicone products are used in all walks of life
2026-10-26 12:13:43
Click:
A custom silicone LED profile quote goes wrong when the enquiry arrives without the section drawing, the strip dimensions or the annual volume. Send those three and the reply is a price; leave any one of them out and the reply becomes a question.
| ManufacturingSince 2012 | FPC range4–28 mm | Temperature−40 to +200 °C | Capacity14 extrusion lines |
Most stalled custom silicone LED profile quotes are not pricing problems. The enquiry carries a photo of an installed channel, no section dimensions, no annual quantity, and a strip described only by its wattage. A stocked section can be priced from a list; a custom section without a drawing is a question, not a request. The same enquiry becomes one reply once those gaps are filled.
A drawing does not have to be a CAD model, but it must fix the geometry that cannot be changed later:
Two-color construction needs the window marked as well: inner height 2.5–2.9 mm, inner width 11–13 mm. If the shape is still open, start from how cross-sections are chosen.
Four strip numbers decide whether a stocked section fits. FPC width: 8, 10 and 12 mm are stocked, while 4–28 mm is the platform. Component height: the 2.8 mm inner height has to clear the tallest part. Diode pitch: it sets how much diffusion the face must add. Construction: single or two-color, since a two-color body is a co-extrusion step rather than one compound. The silicone sleeve for LED strip range shows the stocked widths next to those sections.
Length for a custom silicone LED profile is quoted on the basis the part ships in: square, grooved, D and U sections at 200 m per roll, two-color at 5 m per piece, and the aluminum-channel cover at 100 m per roll. State the cut list as well as the total metres, because a 200 m coil and the same metres cut into 2 m lengths price differently at the packing bench. A bonded joint adds a bonding charge, and it still costs less than moulding the same part. The silicone LED diffuser and sleeve range lists the sections those bases apply to.
Send the first order and the annual usage, not one number. Order value has a floor: a minimum order value of USD 500, measured on value rather than on metres. The annual figure then sets how a new section is quoted, because a first batch and steady running volume are priced on different bases.
Describe the look, not a figure — two parts can share a 2.8 mm inner height and still read differently. Milky and clear are different compounds, two-color construction wraps an opaque body around a diffusing window, and transmittance is adjusted through compound formulation, so "what percentage passes" is answered by the strip and the distance to the face rather than by a catalogue number. Say which effect matters most: dot hiding, color trueness or maximum output.
Silicone parts are produced in-house. End caps, mounting clips and aluminum profiles are integrated through partner suppliers, so state whether the order is extrusion only or an assembly that ships with caps fitted. The second option is quoted as a package and needs the interface dimension, not just the section.
Tooling first: a custom silicone LED profile drawn on a common standard section carries no mould fee, and an unusual one is quoted from the drawing as a separate line. Construction is next — two-color co-extrusion, bonded joints and tight tolerances each add an operation. Volume follows: monthly capacity reaches 8,000,000 meters, so the plant is rarely the constraint, but a small first order still carries set-up. Packing and cut lengths sit at the end of the list.
A usable quotation for a custom silicone LED profile names the section and its drawing revision, then states the unit price per metre or per piece and which basis applies. It carries the minimum order value of USD 500 in the terms, a separate line for tooling or bonding, the packing specified and the trade term. Lead time is quoted against the order type: standard items 5–7 days, in-stock samples 3 days, custom builds 10–20 working days. The validity date belongs on the page.
Three checks catch most mismatches. Put the cavity dimensions against the strip you measured, not the strip in the first email. Confirm whether the price is per metre or per piece, and what the tooling line covers. Then confirm which items come from partner suppliers, so the delivery date reflects two supply chains rather than one.
Minimum order value: USD 500. It is measured as order value rather than metres or pieces, so a short run of a complex section and a long run of a simple one can both be quoted. Add the annual volume to the enquiry so the tooling line can be placed correctly.
A common standard section carries no mould fee. An unusual section is quoted from the drawing with the tooling as a separate line, and two-color construction runs on a separate co-extrusion set-up, so it is quoted as its own line. Ask for the line rather than a lump sum.
Standard items ship in 5–7 days, in-stock samples in 3 days, and custom builds typically take 10–20 working days. Where end caps or a channel are integrated through partner suppliers, the later of the two schedules sets the delivery date.
A sample helps, but it does not replace the cavity measurement. Send the sample with inner width, inner height and wall measured, and mark which face emits. The drawing that follows becomes the reference for both sides once an order is placed.
The silicone extrusion is produced in-house. Aluminum profiles, end caps and clips are integrated through partner suppliers and can ship with the order as an assembly, so state whether you want the extrusion alone or the fitted set.
Send the section drawing or a sample, the strip width and component height, the cut list and the annual volume. If the drawing is still rough, send it anyway — a sketch with the cavity and the emitting face marked is enough to start, and the missing dimension is easier to settle in a reply than in a second email.
Ready for a quote you can act on?
Send the section drawing, the strip dimensions and the annual volume — a stocked 8, 10 or 12 mm width, or a section inside the 4–28 mm platform — and the reply is a price with its basis stated.
DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.
Products Recommended

A custom silicone LED profile quote goes wrong when the enquiry arrives without the section drawing, the strip dimensions or the annual volume. Send those three and the reply is a price; leave any one of them out and the reply becomes a question.
| ManufacturingSince 2012 | FPC range4–28 mm | Temperature−40 to +200 °C | Capacity14 extrusion lines |
Most stalled custom silicone LED profile quotes are not pricing problems. The enquiry carries a photo of an installed channel, no section dimensions, no annual quantity, and a strip described only by its wattage. A stocked section can be priced from a list; a custom section without a drawing is a question, not a request. The same enquiry becomes one reply once those gaps are filled.
A drawing does not have to be a CAD model, but it must fix the geometry that cannot be changed later:
Two-color construction needs the window marked as well: inner height 2.5–2.9 mm, inner width 11–13 mm. If the shape is still open, start from how cross-sections are chosen.
Four strip numbers decide whether a stocked section fits. FPC width: 8, 10 and 12 mm are stocked, while 4–28 mm is the platform. Component height: the 2.8 mm inner height has to clear the tallest part. Diode pitch: it sets how much diffusion the face must add. Construction: single or two-color, since a two-color body is a co-extrusion step rather than one compound. The silicone sleeve for LED strip range shows the stocked widths next to those sections.
Length for a custom silicone LED profile is quoted on the basis the part ships in: square, grooved, D and U sections at 200 m per roll, two-color at 5 m per piece, and the aluminum-channel cover at 100 m per roll. State the cut list as well as the total metres, because a 200 m coil and the same metres cut into 2 m lengths price differently at the packing bench. A bonded joint adds a bonding charge, and it still costs less than moulding the same part. The silicone LED diffuser and sleeve range lists the sections those bases apply to.
Send the first order and the annual usage, not one number. Order value has a floor: a minimum order value of USD 500, measured on value rather than on metres. The annual figure then sets how a new section is quoted, because a first batch and steady running volume are priced on different bases.
Describe the look, not a figure — two parts can share a 2.8 mm inner height and still read differently. Milky and clear are different compounds, two-color construction wraps an opaque body around a diffusing window, and transmittance is adjusted through compound formulation, so "what percentage passes" is answered by the strip and the distance to the face rather than by a catalogue number. Say which effect matters most: dot hiding, color trueness or maximum output.
Silicone parts are produced in-house. End caps, mounting clips and aluminum profiles are integrated through partner suppliers, so state whether the order is extrusion only or an assembly that ships with caps fitted. The second option is quoted as a package and needs the interface dimension, not just the section.
Tooling first: a custom silicone LED profile drawn on a common standard section carries no mould fee, and an unusual one is quoted from the drawing as a separate line. Construction is next — two-color co-extrusion, bonded joints and tight tolerances each add an operation. Volume follows: monthly capacity reaches 8,000,000 meters, so the plant is rarely the constraint, but a small first order still carries set-up. Packing and cut lengths sit at the end of the list.
A usable quotation for a custom silicone LED profile names the section and its drawing revision, then states the unit price per metre or per piece and which basis applies. It carries the minimum order value of USD 500 in the terms, a separate line for tooling or bonding, the packing specified and the trade term. Lead time is quoted against the order type: standard items 5–7 days, in-stock samples 3 days, custom builds 10–20 working days. The validity date belongs on the page.
Three checks catch most mismatches. Put the cavity dimensions against the strip you measured, not the strip in the first email. Confirm whether the price is per metre or per piece, and what the tooling line covers. Then confirm which items come from partner suppliers, so the delivery date reflects two supply chains rather than one.
Minimum order value: USD 500. It is measured as order value rather than metres or pieces, so a short run of a complex section and a long run of a simple one can both be quoted. Add the annual volume to the enquiry so the tooling line can be placed correctly.
A common standard section carries no mould fee. An unusual section is quoted from the drawing with the tooling as a separate line, and two-color construction runs on a separate co-extrusion set-up, so it is quoted as its own line. Ask for the line rather than a lump sum.
Standard items ship in 5–7 days, in-stock samples in 3 days, and custom builds typically take 10–20 working days. Where end caps or a channel are integrated through partner suppliers, the later of the two schedules sets the delivery date.
A sample helps, but it does not replace the cavity measurement. Send the sample with inner width, inner height and wall measured, and mark which face emits. The drawing that follows becomes the reference for both sides once an order is placed.
The silicone extrusion is produced in-house. Aluminum profiles, end caps and clips are integrated through partner suppliers and can ship with the order as an assembly, so state whether you want the extrusion alone or the fitted set.
Send the section drawing or a sample, the strip width and component height, the cut list and the annual volume. If the drawing is still rough, send it anyway — a sketch with the cavity and the emitting face marked is enough to start, and the missing dimension is easier to settle in a reply than in a second email.
Ready for a quote you can act on?
Send the section drawing, the strip dimensions and the annual volume — a stocked 8, 10 or 12 mm width, or a section inside the 4–28 mm platform — and the reply is a price with its basis stated.
DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.
Products Recommended

Products Recommended
Products Recommended
