Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

APPLICATION


Our silicone products are used in all walks of life

APPLICATION


Our silicone products are used in all walks of life

Application Industry

Square, D-Shape, U-Shape and Grooved: Silicone LED Profile Cross-Sections Explained

2026-10-26 12:13:41

Click:

“ A shape-led guide to the silicone LED profile families: square, grooved, D, U, two-color and aluminum channel forms, what each cross-section changes in cavity depth and light spread, and how to read a section drawing before the first sample of a part is quoted. ”

Silicone LED profile · cross-section guide

A silicone LED profile is chosen by its cross-section, not by its brand: the shape sets how far the strip sits from the emitting face, which way the light leaves, and how the part is mounted. This guide compares the seven sections we extrude and the cases each one fits.

ManufacturingSince 2012 FPC range4–28 mm Temperature−40 to +200 °C Extrusion14 extrusion lines

Why does the cross-section decide the project?

Two sections can take the same strip and look nothing alike on site. The geometry of a silicone LED profile fixes three facts before any compound question is asked: the distance from the board to the emitting face, the direction the light leaves, and how the part is fixed. Change the shape and you change the cavity depth, one of the three variables behind an even glow, alongside chip density and wall transmittance. None of the three removes dots on its own; a deeper cavity helps, but a dense strip still sets the ceiling.

So the order of decisions is fixed: strip and section first, compound second. The section also settles the practical side of an order — how the part is cut, packed and whether it can be supplied on a roll. The compound is a transparent silicone: 70±5 Shore A, density 1.2±0.1 g/cm³, tensile strength ≥8 MPa, tear strength ≥30 kN/m, −40 to +200 °C and UL94 HB; ROHS and REACH sit at raw-material level.

What are the seven silicone LED profiles?

The range carries seven sections: four single-color forms, two two-color forms and a lens for aluminum channels. All are extruded. End caps, clips and aluminum are integrated through partner suppliers rather than made here.

Section What the shape changes Stock packing
Square sleeve Symmetric cavity; light leaves face or sides 200 m per roll
Grooved sleeve Open channel one face; strip clips in and can be replaced 200 m per roll
D-shape Curved outer face; widest spread of the line 200 m per roll
U-shape Narrow open channel for a cut slot or an edge 200 m per roll
Two-color square Milky skin over a clear body; second diffusing surface 5 m per PCS
Two-color D The same two-layer wall on the curved face 5 m per PCS
Aluminum channel cover Silicone lens that closes a rigid aluminum housing 100 m per roll

Stock single-color sections run at an inner width of 8.8–13 mm, an inner height of 2.8 mm and a wall of 0.5–0.6 mm. The two-color versions are drawn at 11–13 mm inner width and 2.5–2.9 mm inner height. They are built around 8, 10 and 12 mm printed circuit boards, while the platform covers flexible circuits from 4 mm to 28 mm. The right silicone LED profile for a fixture is the one whose cavity follows the mounting.

When is a square section the right default?

Most projects start here, and most stay. A square sleeve takes the strip straight, keeps the cavity symmetric and leaves two faces to emit from, so it suits a fixture where the light direction is not final yet. Its cavity is the reference depth: a 2.8 mm inner height behind a 0.5–0.6 mm wall. A wider spread or a shallower profile is a new drawing inside the same family, not a different material.

The square form is also the easiest to pack and cut: 200 m per roll, constant section. Where the strip sits in a channel rather than inside a closed tube, the comparison changes, and the flat top emitting direct-lit diffuser family shows the face-lit arrangement.

How does a grooved section hold the strip?

A grooved sleeve carries an open channel down one face. The strip slides in and the channel walls hold it, so no insert and no bonding is needed — this is the form to choose when a strip must be replaced in the field. The trade is cavity: a channel that grips takes height away from the space in front of the board, which is why a grooved section is not the automatic answer for a dense, high-brightness line.

Where the strip has to be slipped in rather than bonded, compare the grooved and square forms. The side-lit flat emitting diffuser range covers the sections that throw light across a mounting surface instead of down the line.

What does a D-shape change?

The outer face curves. That does two things: it widens the spread of the lit line, and it puts more material between the board and the top of the arc than a flat face does at the same inner height. It is the section asked for when the light has to leave over a wide angle — the 270° and 360° versions are made as D-shape and round tube forms. A D-shape does not replace the three variables; it moves one of them, the distance, in a favourable direction. Transmittance is still adjusted through compound formulation, and the strip still sets the ceiling. The wide-angle family is grouped on the 270 D-shape and 360 round silicone neon flex page.

When is a U-shape the only fit?

When the strip has to sit in a slot rather than on a surface. A U-section is a narrow open channel: the fixture is machined with a groove, the U drops in, and the light leaves along the channel axis. It is thinner than a square sleeve around the same strip width, which matters on a thin panel edge, and it is the section to compare when the fixture already exists and the profile has to follow that cut.

When should you choose two-color extrusion?

Two-color extrusion runs a milky diffusing skin over a clear body in one pass. The extra layer gives the light a second surface to cross, which is what designers ask for when the strip is dense and the face is viewed close up. The trade is handling: the two-color forms are supplied at 5 m per PCS rather than on a roll, because the co-extruded skin is worked in short lengths.

When does an aluminum channel make sense?

When the fixture needs a rigid housing. An aluminum channel carries the strip, gives the assembly its straightness and its heat path, and the silicone part becomes the lens that closes it. That lens is supplied at 100 m per roll. The silicone is extruded here; the aluminum, end caps and clips are integrated through partner suppliers, so the assembly ships as one item while only the silicone is made in-house. The lens family is listed on the silicone snap-on cover for LED aluminum profiles page.

How do you read a section drawing?

A section drawing carries four numbers that matter: inner width, inner height, wall thickness and the corner radius. Inner width is set by the strip and its connector. Inner height sets the cavity depth. Wall thickness sits in the 0.5–0.6 mm band on stocked sections. The radius decides how the light leaves a curved form. Read the drawing against the strip datasheet, not a photo, and check connector height before sign-off — a connector standing proud of the board is a common reason a section that fits will not feed.

A drawing that arrives with a strip datasheet is quoted in one round. One that arrives as a photo of a fixture is quoted with assumptions. The words that matter are "inner" and "outer": outer dimensions describe the silhouette, inner dimensions describe what the strip has to pass through.

What goes wrong in a first specification?

Three failures repeat. The first is quoting a section before the strip is fixed, which forces a new drawing. The second is treating an even glow as a property of the section alone: it is the three variables together, and the compound is tuned after the geometry. The third is leaving the finish to the order — clear, milky or two-color changes the compound, and a silicone LED profile quoted without a finish is quoted on an assumption.

A fourth failure is invisible at quotation stage: packing. A 200 m roll and a 5 m PCS use different cartons, cores and pallet counts, so packing belongs in the price.

Frequently asked questions

Is a square section always the best choice?

No. It is the safe default while the light direction is open. A grooved section wins where the strip has to be replaced, a D-shape for a wide spread, a U-shape where the fixture has a machined slot.

Does a D-shape remove visible LED dots?

Not on its own. Dot visibility is set by chip density, the distance from the board to the emitting face and the transmittance of the wall. A D-shape increases the distance; the compound still has to be tuned through compound formulation for each project.

Can two different strips use the same profile?

Only if both fit the cavity and the connector clears it. Stock single-color sections take an inner width of 8.8–13 mm, and the platform covers 4–28 mm circuits. Two strips of the same width may still differ in board thickness, so send both datasheets.

What is the minimum order for a section?

Orders are quoted against a minimum order value of USD 500 rather than a minimum length. Standard sections ship in 5–7 days and in-stock samples in 3 days; custom sections typically take 10–20 working days from an approved drawing.

Are the end caps and clips made in-house?

No. Silicone sections are extruded here; end caps, mounting clips and aluminum channels are integrated through partner suppliers. The assembly can still ship as one item, but only the silicone part is produced in our plant.

Related reading

Next step

Send the strip width and thickness, the chip spacing, the section family and the length per roll. If the section is still open, send the fixture drawing and the direction the light has to leave.

Need the right section for your fixture?

Send the strip width, the mounting and the finish you want — 8, 10 or 12 mm stock sizes, or any width inside the 4–28 mm platform — and we reply with the matching section and compound.

Request a quote → WhatsApp +8618028921514

DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Square, D-Shape, U-Shape and Grooved: Silicone LED Profile Cross-Sections Explained

Author:DongGuan Yutian Silicone Rubber Technology Co.,Ltd

Silicone LED profile · cross-section guide

A silicone LED profile is chosen by its cross-section, not by its brand: the shape sets how far the strip sits from the emitting face, which way the light leaves, and how the part is mounted. This guide compares the seven sections we extrude and the cases each one fits.

ManufacturingSince 2012 FPC range4–28 mm Temperature−40 to +200 °C Extrusion14 extrusion lines

Why does the cross-section decide the project?

Two sections can take the same strip and look nothing alike on site. The geometry of a silicone LED profile fixes three facts before any compound question is asked: the distance from the board to the emitting face, the direction the light leaves, and how the part is fixed. Change the shape and you change the cavity depth, one of the three variables behind an even glow, alongside chip density and wall transmittance. None of the three removes dots on its own; a deeper cavity helps, but a dense strip still sets the ceiling.

So the order of decisions is fixed: strip and section first, compound second. The section also settles the practical side of an order — how the part is cut, packed and whether it can be supplied on a roll. The compound is a transparent silicone: 70±5 Shore A, density 1.2±0.1 g/cm³, tensile strength ≥8 MPa, tear strength ≥30 kN/m, −40 to +200 °C and UL94 HB; ROHS and REACH sit at raw-material level.

What are the seven silicone LED profiles?

The range carries seven sections: four single-color forms, two two-color forms and a lens for aluminum channels. All are extruded. End caps, clips and aluminum are integrated through partner suppliers rather than made here.

Section What the shape changes Stock packing
Square sleeve Symmetric cavity; light leaves face or sides 200 m per roll
Grooved sleeve Open channel one face; strip clips in and can be replaced 200 m per roll
D-shape Curved outer face; widest spread of the line 200 m per roll
U-shape Narrow open channel for a cut slot or an edge 200 m per roll
Two-color square Milky skin over a clear body; second diffusing surface 5 m per PCS
Two-color D The same two-layer wall on the curved face 5 m per PCS
Aluminum channel cover Silicone lens that closes a rigid aluminum housing 100 m per roll

Stock single-color sections run at an inner width of 8.8–13 mm, an inner height of 2.8 mm and a wall of 0.5–0.6 mm. The two-color versions are drawn at 11–13 mm inner width and 2.5–2.9 mm inner height. They are built around 8, 10 and 12 mm printed circuit boards, while the platform covers flexible circuits from 4 mm to 28 mm. The right silicone LED profile for a fixture is the one whose cavity follows the mounting.

When is a square section the right default?

Most projects start here, and most stay. A square sleeve takes the strip straight, keeps the cavity symmetric and leaves two faces to emit from, so it suits a fixture where the light direction is not final yet. Its cavity is the reference depth: a 2.8 mm inner height behind a 0.5–0.6 mm wall. A wider spread or a shallower profile is a new drawing inside the same family, not a different material.

The square form is also the easiest to pack and cut: 200 m per roll, constant section. Where the strip sits in a channel rather than inside a closed tube, the comparison changes, and the flat top emitting direct-lit diffuser family shows the face-lit arrangement.

How does a grooved section hold the strip?

A grooved sleeve carries an open channel down one face. The strip slides in and the channel walls hold it, so no insert and no bonding is needed — this is the form to choose when a strip must be replaced in the field. The trade is cavity: a channel that grips takes height away from the space in front of the board, which is why a grooved section is not the automatic answer for a dense, high-brightness line.

Where the strip has to be slipped in rather than bonded, compare the grooved and square forms. The side-lit flat emitting diffuser range covers the sections that throw light across a mounting surface instead of down the line.

What does a D-shape change?

The outer face curves. That does two things: it widens the spread of the lit line, and it puts more material between the board and the top of the arc than a flat face does at the same inner height. It is the section asked for when the light has to leave over a wide angle — the 270° and 360° versions are made as D-shape and round tube forms. A D-shape does not replace the three variables; it moves one of them, the distance, in a favourable direction. Transmittance is still adjusted through compound formulation, and the strip still sets the ceiling. The wide-angle family is grouped on the 270 D-shape and 360 round silicone neon flex page.

When is a U-shape the only fit?

When the strip has to sit in a slot rather than on a surface. A U-section is a narrow open channel: the fixture is machined with a groove, the U drops in, and the light leaves along the channel axis. It is thinner than a square sleeve around the same strip width, which matters on a thin panel edge, and it is the section to compare when the fixture already exists and the profile has to follow that cut.

When should you choose two-color extrusion?

Two-color extrusion runs a milky diffusing skin over a clear body in one pass. The extra layer gives the light a second surface to cross, which is what designers ask for when the strip is dense and the face is viewed close up. The trade is handling: the two-color forms are supplied at 5 m per PCS rather than on a roll, because the co-extruded skin is worked in short lengths.

When does an aluminum channel make sense?

When the fixture needs a rigid housing. An aluminum channel carries the strip, gives the assembly its straightness and its heat path, and the silicone part becomes the lens that closes it. That lens is supplied at 100 m per roll. The silicone is extruded here; the aluminum, end caps and clips are integrated through partner suppliers, so the assembly ships as one item while only the silicone is made in-house. The lens family is listed on the silicone snap-on cover for LED aluminum profiles page.

How do you read a section drawing?

A section drawing carries four numbers that matter: inner width, inner height, wall thickness and the corner radius. Inner width is set by the strip and its connector. Inner height sets the cavity depth. Wall thickness sits in the 0.5–0.6 mm band on stocked sections. The radius decides how the light leaves a curved form. Read the drawing against the strip datasheet, not a photo, and check connector height before sign-off — a connector standing proud of the board is a common reason a section that fits will not feed.

A drawing that arrives with a strip datasheet is quoted in one round. One that arrives as a photo of a fixture is quoted with assumptions. The words that matter are "inner" and "outer": outer dimensions describe the silhouette, inner dimensions describe what the strip has to pass through.

What goes wrong in a first specification?

Three failures repeat. The first is quoting a section before the strip is fixed, which forces a new drawing. The second is treating an even glow as a property of the section alone: it is the three variables together, and the compound is tuned after the geometry. The third is leaving the finish to the order — clear, milky or two-color changes the compound, and a silicone LED profile quoted without a finish is quoted on an assumption.

A fourth failure is invisible at quotation stage: packing. A 200 m roll and a 5 m PCS use different cartons, cores and pallet counts, so packing belongs in the price.

Frequently asked questions

Is a square section always the best choice?

No. It is the safe default while the light direction is open. A grooved section wins where the strip has to be replaced, a D-shape for a wide spread, a U-shape where the fixture has a machined slot.

Does a D-shape remove visible LED dots?

Not on its own. Dot visibility is set by chip density, the distance from the board to the emitting face and the transmittance of the wall. A D-shape increases the distance; the compound still has to be tuned through compound formulation for each project.

Can two different strips use the same profile?

Only if both fit the cavity and the connector clears it. Stock single-color sections take an inner width of 8.8–13 mm, and the platform covers 4–28 mm circuits. Two strips of the same width may still differ in board thickness, so send both datasheets.

What is the minimum order for a section?

Orders are quoted against a minimum order value of USD 500 rather than a minimum length. Standard sections ship in 5–7 days and in-stock samples in 3 days; custom sections typically take 10–20 working days from an approved drawing.

Are the end caps and clips made in-house?

No. Silicone sections are extruded here; end caps, mounting clips and aluminum channels are integrated through partner suppliers. The assembly can still ship as one item, but only the silicone part is produced in our plant.

Related reading

Next step

Send the strip width and thickness, the chip spacing, the section family and the length per roll. If the section is still open, send the fixture drawing and the direction the light has to leave.

Need the right section for your fixture?

Send the strip width, the mounting and the finish you want — 8, 10 or 12 mm stock sizes, or any width inside the 4–28 mm platform — and we reply with the matching section and compound.

Request a quote → WhatsApp +8618028921514

DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters · 2,600+ customers. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China. Contact: Brown · +8618028921514 · salesmanager@yutiansilicone.com · Not for human implant.

Square, D-Shape, U-Shape and Grooved: Silicone LED Profile Cross-Sections Explained
A shape-led guide to the silicone LED profile families: square, grooved, D, U, two-color and aluminum channel forms, what each cross-section changes in cavity depth and light spread, and how to read a section drawing before the first sample of a part is quoted.
Long by picture save/share
0

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Products Recommended

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

CONTACT


Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

 

  • Mobile:
  • 0086-18028921514
  • Fax:0086-769-82555312
  • Email:salesmanager@yutiansilicone.com

Link: China Edge-lit Lighting, Backlight Lighting Manufa

Contact Us

Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

 

  • Mobile/Whatsapp:
    0086-18028921514
  • Fax:86-769-89221009
  • Email:salesmanager@yutiansilicone.com

 

Copyright © 2015-2026 All Rights Reserved.

Copyright © 2015-2026 All Rights Reserved.   

Service Center

Please choose online customer service to communicate

Contacts
Phone
+8618028921514
Service time
From Monday to Sunday
E-mail
salesmanager@yutiansilicone.com
Scan a QR Code
Qrcode
WhatsApp
Add WeChat friend to learn more about the product
Use Enterprise WeChat
"Scan" to join the group chat
Copy success!
Add WeChat friend to learn more about the product
I see.