Demand Submission


Please leave us a message and we will contact you within 24 hours

  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Do you have any comments or questions

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

APPLICATION


Our silicone products are used in all walks of life

APPLICATION


Our silicone products are used in all walks of life

Application Industry

Braided vs Reinforced vs Steel Wire Silicone Hose: Which One Do You Need?

2026-10-22 12:07:15

Click:

“ Polyester braid, mesh braid and steel wire braid are three separate constructions, each with its own models, size range and burst data. This guide compares all three: ID 3–31.75 mm for polyester braid, ID 19–102 mm for mesh and wire, and how to choose. ”

Technical Guide  ·  Selection & Comparison

If you are comparing braided vs reinforced silicone hose, start here: reinforced is the general category, braided is one type of it. We build three separate constructions, each with its own bore range and burst data: polyester braid from ID 3 mm to 31.75 mm, mesh braid and steel wire braid from ID 19 mm to 102 mm.

Polyester braidID 3–31.75 mm11 models · burst ≥12–38 kg/cm²Mesh braidID 19–102 mm7 models · burst ≥5–15 kg/cm²Steel wire braidID 19–102 mm7 models · burst ≥6–25 kg/cm²Shared by all three−40 to +200 °CPlatinum-cured silicone

Braided vs reinforced silicone hose: the words are not interchangeable

Search results use the two terms as if they were synonyms, and that is how buyers end up comparing the wrong data sheets. The distinction is short:

  • Reinforced silicone hose — any silicone hose with a load-bearing layer between the inner tube and the outer jacket. That layer can be braided yarn, woven fabric or metal wire.
  • Braided silicone hose — a reinforced hose whose load-bearing layer is interwoven yarn, usually high-temperature polyester. Every braided hose is reinforced; not every reinforced hose is braided.
  • Steel wire braided hose — a reinforced hose whose layer is stainless steel wire. It is still braided, but it is a different construction with its own models and its own ordering route.

The yarn itself is a material choice, not a construction. Polyester yarn is our standard; cotton yarn and nylon yarn can be supplied on request, both used in food and medical contact work at the same −40 °C to +200 °C. Burst data in this article covers the polyester yarn models; for cotton and nylon we measure per specification.

Three silicone hose reinforcement types, three separate specifications

The three silicone hose reinforcement types are not interchangeable, and their numbers do not cross over. Size range and burst range differ because the reinforcement layer and the bore range differ. What the three constructions do share is the silicone compound and the braided silicone hose temperature range: all are platinum-cured, and all run −40 °C to +200 °C (−40 °F to 392 °F). Read the table below as three separate windows, then use the model table for the construction you actually need.

Table 1. Three constructions, three published ranges. Each row is a separate construction with its own models and burst data; figures are not interchangeable between rows.
ConstructionReinforcement layerModelsID (mm)Burst (kg/cm²)Burst (MPa)Wall (mm)
Polyester braidBraided high-temperature polyester yarn113–31.75≥ 12–381.18–3.732.5–7.125
Mesh braidWoven polyester fabric719–102≥ 5–150.49–1.474.5
Steel wire braid304 stainless steel spiral wire plus polyester fabric719–102≥ 6–250.59–2.455–6

In practice a request that asks only for "reinforced hose" comes back as a polyester braid, because that is the standard construction. If your line needs the larger bores, say mesh or steel wire in the first message.

Polyester braid: the standard construction, eleven models

Polyester braid is the three-layer build: a platinum-cured silicone inner layer, a high-temperature polyester braid and a silicone outer jacket. It is our standard reinforced hose, published in eleven models from ID 3 mm to ID 31.75 mm, and it is the only construction of the three that covers bores below ID 19 mm.

Burst pressure falls as the bore grows, because the same wall carries less load as diameter rises. A 3 mm line and a 31.75 mm line should never be quoted from the same figure, which is why every model is listed separately below.

Table 2. Polyester braid, HJBX-001 to HJBX-011. Minimum burst is given in kg/cm² with the MPa equivalent beside it. Tolerances as published; packaging 1–15 m per bag.
ModelID (mm)OD (mm)Wall (mm)Burst (kg/cm²)Burst (MPa)Bend radius (mm)
HJBX-0013 ± 0.58 ± 0.52.5≥ 383.7335
HJBX-0024 ± 0.59 ± 0.52.5≥ 383.7335
HJBX-0035 ± 0.511 ± 0.53≥ 383.7335
HJBX-0046.35 ± 0.512 ± 0.52.825≥ 353.4335
HJBX-0057.93 ± 0.515 ± 0.53.535≥ 353.4350
HJBX-0069.52 ± 0.517 ± 0.53.74≥ 353.4350
HJBX-00712.7 ± 0.722 ± 0.74.65≥ 252.4570
HJBX-00815.87 ± 0.725 ± 0.74.565≥ 232.2680
HJBX-00919.05 ± 0.731 ± 0.75.975≥ 181.77110
HJBX-01025.4 ± 0.738 ± 0.76.3≥ 121.18150
HJBX-01131.75 ± 0.746 ± 0.77.125≥ 121.18200

Bend radius runs from 35 mm to 200 mm across the eleven models. The compound is medical and food grade with ROHS, FDA, LFGB and NSF compliance, and all eleven models suit full vacuum.

Mesh braid: seven models from ID 19 mm to ID 102 mm

Mesh braid uses woven polyester fabric as the reinforcement layer instead of braided yarn, bonded over the same platinum-cured silicone bore. The mesh braided hose sizes run from ID 19 mm to ID 102 mm in seven models, with a 4.5 mm wall throughout and minimum burst from 5 to 15 kg/cm² (0.49 to 1.47 MPa).

Table 3. Mesh braid, YT-GB-4019 to YT-GB-4102. Minimum burst in kg/cm² with the MPa equivalent beside it; packaging 1–4 m.
ModelID (mm)OD (mm)Wall (mm)Burst (kg/cm²)Burst (MPa)Bend radius (mm)
YT-GB-401919284.5≥ 151.4754
YT-GB-402525344.5≥ 131.2790
YT-GB-403535444.5≥ 111.08161
YT-GB-404040494.5≥ 90.88200
YT-GB-405151604.5≥ 70.69245
YT-GB-407676854.5≥ 60.59308
YT-GB-41021021114.5≥ 50.49360

The thin wall gives mesh braid a tighter bend radius than steel wire at the same bore, 54 mm against 89 mm at ID 19 mm, so it is the flexible option where large diameter braided hose has to follow a route.

Steel wire braid: spiral 304 wire, seven models

Steel wire braid is built as a spiral 304 stainless steel wire reinforcement with polyester braid fabric, over the same platinum-cured silicone bore. The steel wire braided hose sizes follow the same seven bores as the mesh construction, ID 19 mm to ID 102 mm, with a 5 mm wall up to ID 51 mm and 6 mm above that. Minimum burst runs from 6 to 25 kg/cm² (0.59 to 2.45 MPa).

Table 4. Steel wire braid, YT-GB-5019 to YT-GB-5102. Minimum burst in kg/cm² with the MPa equivalent beside it; packaging 1–4 m.
ModelID (mm)OD (mm)Wall (mm)Burst (kg/cm²)Burst (MPa)Bend radius (mm)
YT-GB-501919295≥ 252.4589
YT-GB-502525355≥ 222.16127
YT-GB-503535455≥ 181.77178
YT-GB-504040505≥ 171.67214
YT-GB-505151615≥ 141.37280
YT-GB-507676886≥ 90.88432
YT-GB-51021021146≥ 60.59508

Two differences matter. At the same bore steel wire carries a higher minimum burst than mesh, 25 against 15 kg/cm² at ID 19 mm, and the spiral wire supports the wall against vacuum collapse. The trade-off is stiffness: the braided hose bend radius runs from 89 mm to 508 mm, wider than mesh at every bore.

Braided hose selection criteria

The braided hose selection criteria below follow the bore ranges printed in tables 2 to 4. Work down the list and stop at the first line that describes your duty.

  1. Bore below ID 19 mm — polyester braid. The mesh and steel wire ranges start at ID 19 mm, so a small-bore line has one construction available from this range.
  2. Ambient transfer, cooling circuits, light vacuum or a route with tight bends — polyester braid. It is the standard for kink and vacuum resistance on small and medium bores.
  3. Liquid or semi-liquid transfer at ID 19–102 mm with a moderate pressure duty — mesh braid. The 4.5 mm wall keeps the hose flexible on long runs.
  4. The same large bore where the line must hold vacuum, or where pressure duty is higher — steel wire braid. The spiral wire does the structural work.
  5. A line that must hold shape under load, or a high pressure silicone hose duty — steel wire braid, quoted against your specification as a custom braided silicone hose.
  6. Medium, temperature, pressure or vacuum outside the published ranges — send the duty to us. The construction is decided before price enters the conversation.

What the braid changes, and what it does not

Table 5. Plain silicone tubing against a reinforced construction. Qualitative comparison; the published minimum burst per model is in tables 2 to 4.
PropertyPlain silicone tubingReinforced hose
Burst resistanceLimited by the silicone wall aloneRaised by the reinforcement layer
Vacuum and collapseCollapses under strong vacuumResists collapse; suitable for full vacuum
Kink resistanceKinks at tight bend radiiHolds the bore open at tighter bends
FlexibilitySofter in handStiffer — the trade-off for the strength

The honest limit: the reinforcement raises burst resistance, vacuum resistance and kink resistance, but how much depends on the bore, the wall and the duty cycle, which is why we publish a minimum burst per model rather than a multiplier.

Burst pressure is not working pressure

Every burst figure here is a minimum failure threshold, not a working rating: size the line from the working pressure and apply the safety factor your own standard requires. Vacuum is a separate failure mode, and the braid or the spiral wire is what keeps the bore open.

What to send for a quotation

Whether the answer is polyester, mesh or steel wire, these inputs decide it:

  • Bore and wall — ID and OD, or ID and wall thickness, with the tolerance you accept.
  • Working pressure and peak pressure — stated separately from any burst figure.
  • Vacuum level, if the line goes negative.
  • Temperature — continuous and peak, and whether it is the medium or the ambient that is hot.
  • Medium and bend radius in the installation, not on a bench.
  • Connection type — we manufacture the silicone hose; fittings, clamps and other non-silicone parts can be integrated through our partner network, but they are not made in our factory.
  • Certification and cleanliness — cleanroom production, ISO 10993 biocompatibility reports (cytotoxicity, skin sensitization, skin irritation) and ISO 13485 documentation can be provided according to customer requirements.
  • Length per piece, packaging and quantity — 1–15 m per bag for polyester braid, 1–4 m for mesh and steel wire.

Frequently asked questions

Are braided and reinforced silicone hose the same thing?

No. Reinforced is the general term for any silicone hose with a load-bearing layer between the inner tube and the outer jacket. Braided describes how that layer is made: interwoven yarn. Every braided hose is reinforced, but a mesh fabric or a steel wire layer is also a reinforcement.

Do the three constructions share one specification?

No. Each construction has its own models, its own bore range and its own burst range: polyester braid ID 3–31.75 mm, mesh braid and steel wire braid ID 19–102 mm. What they share is the platinum-cured silicone compound and the continuous −40 °C to +200 °C range.

Which construction covers a bore under 19 mm?

Polyester braid. The eleven models run from ID 3 mm to ID 31.75 mm, and the mesh and steel wire ranges start at ID 19 mm. For a small-bore line the polyester braid is the only construction in this range.

What is the minimum burst of each construction?

Polyester braid is rated at ≥ 12–38 kg/cm² (1.18–3.73 MPa), mesh braid at ≥ 5–15 kg/cm² (0.49–1.47 MPa) and steel wire braid at ≥ 6–25 kg/cm² (0.59–2.45 MPa). Each range covers the models of that construction only.

Is the burst pressure the working pressure?

No. Burst pressure is the failure threshold. Size the line from the working pressure and apply the safety factor your own standard requires. Treat the burst figure as a ceiling for comparison between candidate models.

Can the reinforcement yarn be changed?

Yes. Polyester yarn is the standard; cotton yarn and nylon yarn can be supplied on request, both used in food and medical contact work at the same −40 °C to +200 °C. Burst data is published for the polyester yarn models; other yarns are measured per specification.

Related reading

Next step

Send the bore and wall, the working and peak pressure, the vacuum level, the medium, the temperature, the installed bend radius and the certifications you need. We will tell you which construction fits — polyester braid, mesh braid or steel wire braid — and quote it with the applicable lead time.

Not sure which construction you need?

Send your bore, pressure, vacuum and temperature; we reply with the matching construction, its model table and the lead time.

Ask us which construction fits →WhatsApp +8618028921514

DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2 Tutang Industrial 2nd Heng Road, Changping Town, Dongguan, Guangdong, China. Not for human implant.

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Braided vs Reinforced vs Steel Wire Silicone Hose: Which One Do You Need?

Author:DongGuan Yutian Silicone Rubber Technology Co.,Ltd

Technical Guide  ·  Selection & Comparison

If you are comparing braided vs reinforced silicone hose, start here: reinforced is the general category, braided is one type of it. We build three separate constructions, each with its own bore range and burst data: polyester braid from ID 3 mm to 31.75 mm, mesh braid and steel wire braid from ID 19 mm to 102 mm.

Polyester braidID 3–31.75 mm11 models · burst ≥12–38 kg/cm²Mesh braidID 19–102 mm7 models · burst ≥5–15 kg/cm²Steel wire braidID 19–102 mm7 models · burst ≥6–25 kg/cm²Shared by all three−40 to +200 °CPlatinum-cured silicone

Braided vs reinforced silicone hose: the words are not interchangeable

Search results use the two terms as if they were synonyms, and that is how buyers end up comparing the wrong data sheets. The distinction is short:

  • Reinforced silicone hose — any silicone hose with a load-bearing layer between the inner tube and the outer jacket. That layer can be braided yarn, woven fabric or metal wire.
  • Braided silicone hose — a reinforced hose whose load-bearing layer is interwoven yarn, usually high-temperature polyester. Every braided hose is reinforced; not every reinforced hose is braided.
  • Steel wire braided hose — a reinforced hose whose layer is stainless steel wire. It is still braided, but it is a different construction with its own models and its own ordering route.

The yarn itself is a material choice, not a construction. Polyester yarn is our standard; cotton yarn and nylon yarn can be supplied on request, both used in food and medical contact work at the same −40 °C to +200 °C. Burst data in this article covers the polyester yarn models; for cotton and nylon we measure per specification.

Three silicone hose reinforcement types, three separate specifications

The three silicone hose reinforcement types are not interchangeable, and their numbers do not cross over. Size range and burst range differ because the reinforcement layer and the bore range differ. What the three constructions do share is the silicone compound and the braided silicone hose temperature range: all are platinum-cured, and all run −40 °C to +200 °C (−40 °F to 392 °F). Read the table below as three separate windows, then use the model table for the construction you actually need.

Table 1. Three constructions, three published ranges. Each row is a separate construction with its own models and burst data; figures are not interchangeable between rows.
ConstructionReinforcement layerModelsID (mm)Burst (kg/cm²)Burst (MPa)Wall (mm)
Polyester braidBraided high-temperature polyester yarn113–31.75≥ 12–381.18–3.732.5–7.125
Mesh braidWoven polyester fabric719–102≥ 5–150.49–1.474.5
Steel wire braid304 stainless steel spiral wire plus polyester fabric719–102≥ 6–250.59–2.455–6

In practice a request that asks only for "reinforced hose" comes back as a polyester braid, because that is the standard construction. If your line needs the larger bores, say mesh or steel wire in the first message.

Polyester braid: the standard construction, eleven models

Polyester braid is the three-layer build: a platinum-cured silicone inner layer, a high-temperature polyester braid and a silicone outer jacket. It is our standard reinforced hose, published in eleven models from ID 3 mm to ID 31.75 mm, and it is the only construction of the three that covers bores below ID 19 mm.

Burst pressure falls as the bore grows, because the same wall carries less load as diameter rises. A 3 mm line and a 31.75 mm line should never be quoted from the same figure, which is why every model is listed separately below.

Table 2. Polyester braid, HJBX-001 to HJBX-011. Minimum burst is given in kg/cm² with the MPa equivalent beside it. Tolerances as published; packaging 1–15 m per bag.
ModelID (mm)OD (mm)Wall (mm)Burst (kg/cm²)Burst (MPa)Bend radius (mm)
HJBX-0013 ± 0.58 ± 0.52.5≥ 383.7335
HJBX-0024 ± 0.59 ± 0.52.5≥ 383.7335
HJBX-0035 ± 0.511 ± 0.53≥ 383.7335
HJBX-0046.35 ± 0.512 ± 0.52.825≥ 353.4335
HJBX-0057.93 ± 0.515 ± 0.53.535≥ 353.4350
HJBX-0069.52 ± 0.517 ± 0.53.74≥ 353.4350
HJBX-00712.7 ± 0.722 ± 0.74.65≥ 252.4570
HJBX-00815.87 ± 0.725 ± 0.74.565≥ 232.2680
HJBX-00919.05 ± 0.731 ± 0.75.975≥ 181.77110
HJBX-01025.4 ± 0.738 ± 0.76.3≥ 121.18150
HJBX-01131.75 ± 0.746 ± 0.77.125≥ 121.18200

Bend radius runs from 35 mm to 200 mm across the eleven models. The compound is medical and food grade with ROHS, FDA, LFGB and NSF compliance, and all eleven models suit full vacuum.

Mesh braid: seven models from ID 19 mm to ID 102 mm

Mesh braid uses woven polyester fabric as the reinforcement layer instead of braided yarn, bonded over the same platinum-cured silicone bore. The mesh braided hose sizes run from ID 19 mm to ID 102 mm in seven models, with a 4.5 mm wall throughout and minimum burst from 5 to 15 kg/cm² (0.49 to 1.47 MPa).

Table 3. Mesh braid, YT-GB-4019 to YT-GB-4102. Minimum burst in kg/cm² with the MPa equivalent beside it; packaging 1–4 m.
ModelID (mm)OD (mm)Wall (mm)Burst (kg/cm²)Burst (MPa)Bend radius (mm)
YT-GB-401919284.5≥ 151.4754
YT-GB-402525344.5≥ 131.2790
YT-GB-403535444.5≥ 111.08161
YT-GB-404040494.5≥ 90.88200
YT-GB-405151604.5≥ 70.69245
YT-GB-407676854.5≥ 60.59308
YT-GB-41021021114.5≥ 50.49360

The thin wall gives mesh braid a tighter bend radius than steel wire at the same bore, 54 mm against 89 mm at ID 19 mm, so it is the flexible option where large diameter braided hose has to follow a route.

Steel wire braid: spiral 304 wire, seven models

Steel wire braid is built as a spiral 304 stainless steel wire reinforcement with polyester braid fabric, over the same platinum-cured silicone bore. The steel wire braided hose sizes follow the same seven bores as the mesh construction, ID 19 mm to ID 102 mm, with a 5 mm wall up to ID 51 mm and 6 mm above that. Minimum burst runs from 6 to 25 kg/cm² (0.59 to 2.45 MPa).

Table 4. Steel wire braid, YT-GB-5019 to YT-GB-5102. Minimum burst in kg/cm² with the MPa equivalent beside it; packaging 1–4 m.
ModelID (mm)OD (mm)Wall (mm)Burst (kg/cm²)Burst (MPa)Bend radius (mm)
YT-GB-501919295≥ 252.4589
YT-GB-502525355≥ 222.16127
YT-GB-503535455≥ 181.77178
YT-GB-504040505≥ 171.67214
YT-GB-505151615≥ 141.37280
YT-GB-507676886≥ 90.88432
YT-GB-51021021146≥ 60.59508

Two differences matter. At the same bore steel wire carries a higher minimum burst than mesh, 25 against 15 kg/cm² at ID 19 mm, and the spiral wire supports the wall against vacuum collapse. The trade-off is stiffness: the braided hose bend radius runs from 89 mm to 508 mm, wider than mesh at every bore.

Braided hose selection criteria

The braided hose selection criteria below follow the bore ranges printed in tables 2 to 4. Work down the list and stop at the first line that describes your duty.

  1. Bore below ID 19 mm — polyester braid. The mesh and steel wire ranges start at ID 19 mm, so a small-bore line has one construction available from this range.
  2. Ambient transfer, cooling circuits, light vacuum or a route with tight bends — polyester braid. It is the standard for kink and vacuum resistance on small and medium bores.
  3. Liquid or semi-liquid transfer at ID 19–102 mm with a moderate pressure duty — mesh braid. The 4.5 mm wall keeps the hose flexible on long runs.
  4. The same large bore where the line must hold vacuum, or where pressure duty is higher — steel wire braid. The spiral wire does the structural work.
  5. A line that must hold shape under load, or a high pressure silicone hose duty — steel wire braid, quoted against your specification as a custom braided silicone hose.
  6. Medium, temperature, pressure or vacuum outside the published ranges — send the duty to us. The construction is decided before price enters the conversation.

What the braid changes, and what it does not

Table 5. Plain silicone tubing against a reinforced construction. Qualitative comparison; the published minimum burst per model is in tables 2 to 4.
PropertyPlain silicone tubingReinforced hose
Burst resistanceLimited by the silicone wall aloneRaised by the reinforcement layer
Vacuum and collapseCollapses under strong vacuumResists collapse; suitable for full vacuum
Kink resistanceKinks at tight bend radiiHolds the bore open at tighter bends
FlexibilitySofter in handStiffer — the trade-off for the strength

The honest limit: the reinforcement raises burst resistance, vacuum resistance and kink resistance, but how much depends on the bore, the wall and the duty cycle, which is why we publish a minimum burst per model rather than a multiplier.

Burst pressure is not working pressure

Every burst figure here is a minimum failure threshold, not a working rating: size the line from the working pressure and apply the safety factor your own standard requires. Vacuum is a separate failure mode, and the braid or the spiral wire is what keeps the bore open.

What to send for a quotation

Whether the answer is polyester, mesh or steel wire, these inputs decide it:

  • Bore and wall — ID and OD, or ID and wall thickness, with the tolerance you accept.
  • Working pressure and peak pressure — stated separately from any burst figure.
  • Vacuum level, if the line goes negative.
  • Temperature — continuous and peak, and whether it is the medium or the ambient that is hot.
  • Medium and bend radius in the installation, not on a bench.
  • Connection type — we manufacture the silicone hose; fittings, clamps and other non-silicone parts can be integrated through our partner network, but they are not made in our factory.
  • Certification and cleanliness — cleanroom production, ISO 10993 biocompatibility reports (cytotoxicity, skin sensitization, skin irritation) and ISO 13485 documentation can be provided according to customer requirements.
  • Length per piece, packaging and quantity — 1–15 m per bag for polyester braid, 1–4 m for mesh and steel wire.

Frequently asked questions

Are braided and reinforced silicone hose the same thing?

No. Reinforced is the general term for any silicone hose with a load-bearing layer between the inner tube and the outer jacket. Braided describes how that layer is made: interwoven yarn. Every braided hose is reinforced, but a mesh fabric or a steel wire layer is also a reinforcement.

Do the three constructions share one specification?

No. Each construction has its own models, its own bore range and its own burst range: polyester braid ID 3–31.75 mm, mesh braid and steel wire braid ID 19–102 mm. What they share is the platinum-cured silicone compound and the continuous −40 °C to +200 °C range.

Which construction covers a bore under 19 mm?

Polyester braid. The eleven models run from ID 3 mm to ID 31.75 mm, and the mesh and steel wire ranges start at ID 19 mm. For a small-bore line the polyester braid is the only construction in this range.

What is the minimum burst of each construction?

Polyester braid is rated at ≥ 12–38 kg/cm² (1.18–3.73 MPa), mesh braid at ≥ 5–15 kg/cm² (0.49–1.47 MPa) and steel wire braid at ≥ 6–25 kg/cm² (0.59–2.45 MPa). Each range covers the models of that construction only.

Is the burst pressure the working pressure?

No. Burst pressure is the failure threshold. Size the line from the working pressure and apply the safety factor your own standard requires. Treat the burst figure as a ceiling for comparison between candidate models.

Can the reinforcement yarn be changed?

Yes. Polyester yarn is the standard; cotton yarn and nylon yarn can be supplied on request, both used in food and medical contact work at the same −40 °C to +200 °C. Burst data is published for the polyester yarn models; other yarns are measured per specification.

Related reading

Next step

Send the bore and wall, the working and peak pressure, the vacuum level, the medium, the temperature, the installed bend radius and the certifications you need. We will tell you which construction fits — polyester braid, mesh braid or steel wire braid — and quote it with the applicable lead time.

Not sure which construction you need?

Send your bore, pressure, vacuum and temperature; we reply with the matching construction, its model table and the lead time.

Ask us which construction fits →WhatsApp +8618028921514

DongGuan Yutian Silicone Rubber Technology Co., Ltd — silicone extrusion manufacturer since 2012. 6,800 m² facility · 14 extrusion lines · 4 calendering lines · 7 compression moulding lines · production team 90+ · management and sales team 50+ · Class 100,000 cleanroom · monthly capacity up to 8,000,000 meters. Certifications: FDA, ROHS, REACH, NSF, LFGB, ISO 13485, ISO 9001, ISO 14001:2015, and ISO 10993 biocompatibility — three reports (cytotoxicity, skin sensitization, skin irritation). Room 801, Building 10, No. 2 Tutang Industrial 2nd Heng Road, Changping Town, Dongguan, Guangdong, China. Not for human implant.

Braided vs Reinforced vs Steel Wire Silicone Hose: Which One Do You Need?
Polyester braid, mesh braid and steel wire braid are three separate constructions, each with its own models, size range and burst data. This guide compares all three: ID 3–31.75 mm for polyester braid, ID 19–102 mm for mesh and wire, and how to choose.
Long by picture save/share
0

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

Products Recommended

Products Recommended

INQUIRY

在线询盘 MORE+
  • Name *

  • Email *

  • Phone

  • Purpose *

    Purpose *

  • Detailed requirements

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

Inquiry Content:


You have no items to require

Add Successfully

CONTACT


Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

 

  • Mobile:
  • 0086-18028921514
  • Fax:0086-769-82555312
  • Email:salesmanager@yutiansilicone.com

Link: China Edge-lit Lighting, Backlight Lighting Manufa

Contact Us

Address:Room 801, Building 10, No. 2, Tutang Industrial 2nd Heng Road, Changping Town, Dongguan City, Guangdong Province, China

 

  • Mobile/Whatsapp:
    0086-18028921514
  • Fax:86-769-89221009
  • Email:salesmanager@yutiansilicone.com

 

Copyright © 2015-2026 All Rights Reserved.

Copyright © 2015-2026 All Rights Reserved.   

Service Center

Please choose online customer service to communicate

Contacts
Phone
+8618028921514
Service time
From Monday to Sunday
E-mail
salesmanager@yutiansilicone.com
Scan a QR Code
Qrcode
WhatsApp
Add WeChat friend to learn more about the product
Use Enterprise WeChat
"Scan" to join the group chat
Copy success!
Add WeChat friend to learn more about the product
I see.